Search results

Ok, so I got then engine in the Supra rebuilt after spinning a rod bearing. Before the build it ran great. No problems what so ever. Spun a bearing and poof, time for a rebuild. Stock type build, .20 over stock pistons, rods, 1.4 mhg and arp's throughout. It runs great, pulls harder than before...

I have been reading through alot of threads and people hint at it, but nobody says where they get the filter head or relocation kit with the temp sensor port in the top of it.....I am running -10an lines with mocal thermostat and wanted to have a guage showing what my oil temp is. I can't find a...

Well, I've been building my engine for the last year. It will have eagle rods , je's coated, arp everything, etc., etc. I will be starting with stock everything on the exterior but upgraded inside the block. Would my stock BOV stand up to the modding after I install 550's, lex, AFPR, maft-pro...

I've seen this car on SM for awhile now and i'd like to know more....anybody got an idea on whos it is?

When i pulled my old turbo engine and tranny out last year, i never thought about it. Guy that had the car before me told me he had a rps clutch kit installed when he did the MHG, front, rear mains, and oil pump. Well, he didnt. I saw a stock toyota pp and just pulled it off and dropped it on...

I've been checking out the " these are the best tanabe springs, and koni struts your can use'" or the " EiBach springs with tokiko's are the best". I want to drop the ride but i don't want to lose traction. I like the way the front drops with my eibach in my n/a yeah, but will my stock springs...

Entitled:'Twas the Night before Christmas, And Santa's Pissed Twas the night before Christmas old Santa was pissed, He cussd out the elves and threw down his list. Miserable little brats, Ungrateful little jerks. I have a good mind, To scrap the whole works. I've busted my ass...

A friend of mine is doing a n/a-turbo swap in his 87 Supe. He asked me and i didn't think it was possible. Can you use a turbo auto harness with a turbo manny ecu in it ? He has a 7mgte engine and manual tranny in it. He baught a ECU and harness but got a AUTO harness with a MANUAL ecu. Is there...

Well, i'm going to be replacing my old valve stem seals but.......as most of you know you CAN NOT use a standard valve spring compressor tool ( unless you distroy a deep well socket )and Toyota does not have a new part number nor do they know where to get one. Has anybody ever purchased/rented...

GOT IT ! bad AFM. Thanks guys

Well, alot of you know that im a N/A guy thats swapping a GTE into my car. I got a 87 turbo car for a steal and found it had a BHG. When i pulled it, i opened the oil drain plug and got the milkshake pouring out. The guy i got the car from said he blew it and it sat for about 6 months before i...

I've searched alot and only found one thread about them, but it doesn't state who makes them. I saw awhile ago that MDC makes a rebuild kit........i can't find it on the site. Does MDC make them or is there somebody else that you know about ?

Yeah i know...........everybody says search first and ask questions later. Well , i searched and all i found is a code 14 for turbo models. This is really stumping me. I've had a miss in the engine for the last 3 months and i finally got it straightened out. New plugs, wires, cap and rotor...

Well im getting ready to do my 5-spd swap into my N/A untill my turbo engine is built, But.......i got all the bolts, brackets, electrical lines, etc. outta the way.....got the tranny back 3-4 inches and it stopped. It wont go back in and it wont come out. Had somebody tell me to take out the...

Well, i keep hearing people talk about some kind of jdm voltage stabilier all the time. What does it do and do they actually work ? If its an inexpensive way to improve the electrical system i might look into getting one.

Well, i'm planning on revamping my interior....ya know , new seats, Panels, Boots, Arm rest, etc. I'm gonna get the e-brake and shift boot from Empera. I gotta friend that says his old (02) RSX seats would fit pretty good in my supra, plus they are black leather -thats sweet- since im going...

I've had my N/A for about 4 yrs now, and 6-8 months on my "JDM" engine. This is the first time i've ever had a misfire at idle while the engine is at normal operating temp. While it's in drive ,it does it more, neutral or park not as much, but it still does it. No engine codes, TPS adjusted to...

Guys and gals, i bought my turbo project with some old school MOMO wheels on it and i can't find any info on them. They are missing 3 of the 4 center caps and the only good pic i have is the one below. Anybody know where or when these were made or sold ?

Well, I figured since im rebuilding my turbo engine and doing suspension work I might as well do the frt/rear bushings and upper/lower ball joints, BUT I cant find any bushing for the damn lower control arms ! I tried toyota and they told me they only have full frt/rear , upper/lower and frt or...

Well, Im getting my turbo going soon and i was wondering what brand of wideband to go with. Innovative has a good kit and so does AEM. What else is out there that i can use and can you provide me some information and part numbers on them. Thanks all