Search results

I have a aristo 2jzgte single turbo with mkiv pump, afpr, 650cc, new o2 sensor and other mods on stock ecu. Lately ive just been breaking in the motor after a fresh rebuild afrs look good at cold start, idle and cruise (14-15). So far so good after 400mi. My only concern is after ive driven it...

Have a aristo 2jzgte on a stand that I am going with a BW s200sx single turbo, 650cc side feed drop ins, stock internals with intake and exhaust of course just the regular BPU's going I my 91 mk3 which will be my DD. Looking for the Earls Sandwich Adapter with the built in thermostat fits the...

Am planning on going with a ebay 2jzgte cast manifold for my single setup and have a question. There is one by godspeed which is $170 and one by boostmasters which is $120 but they look the exact same as some others as well, are they? here is the links...

What's a garrett 60-1 turbo and a garrett TO4E turbo? Found them on the treadstone performance website and was curious because i cant find these turbos on the garrett website? they usually name their turbos i.e. GT3776 or GTX3576R. Im trying to get a good size turbo for my mk3 2jzgte swap and i...

so I just found out today my aristo twins are leaking oil bad on my 1991 supra swap. Just after 10min of running for the for the first time since the swap it has a puddle of oil in the intercooler and I have the stock BOV vented to atmosphere which spewed oil across the heatsheild. So now I'm...

im fabricating my 2.5" intercooler pipe and I have the cold side done and ready to be welded. my question is should I have it all welded one piece from the throttle body to the intercooler which is my current choice or should I make it a two piece for the cold side with a hump coupler between...

anyone have any expirence with these OCC. they seem to be good quality for the price. For starters its baffled, also instead of a sight glass it includes a dipstick, and comes with two 15mm and two 9mm fittings depending on size you need. I figured it would be great for my stock 2jzgte swap...

Ive read that stock jdm non-vvti twins boost creep with no cat exhaust due to the lack of backpressure. how true is this, cause I was planning on going with the driftmotion aristo stock twin downpipe with a 3in exhaust the whole way. if they do would fitting a cat at the end of the DM downpipe...

have a swapped aristo 2jzgte nonvvti that cranks no start. have ignition pulse and injector pulse. checked resistance of crank and both cam sensors. found my map sensor had the rubber stuff torn on the bottom and didnt hold vacuum, so i ordered a used one. checked the connector for the 5V...

i have an aristo 2jz turbo that im about to mate the harness to my body plugs for my 1991 supra turbo. i have the motor on the stand complete now and my question is should i mate the harnesses with the engine out or should i wait till i drop the motor in and see how much wire i need to ready the...

im swappin in a 2jzgte into my 91 supra and so im getting all the fuel system situated. the car has been sitting for two years with half a tank of gas and no additives, yes I know that's a problem but back then didn't know what I was doing. so now I dropped the gas tank and it didn't looked to...

first to start i have been looking for ways to get more angle out of my 1991 supra 2jzgte swap to drift and DD since i know mk3's dont have the best turning radius. i have some info on the supra mk3 racks. apparently from 87 to 91 the racks got a little more steering travel and i was looking...

quick question. started repairing my ignition wires on my aristo 2jzgte engine harness and forgot which pin goes where at the ignition coil connector. does the power wire go to slot 1 or 2 at the connector? and gonna assume the slightly thicker gauge wire is the power wire correct?

i have the aristo 2jzgte ac compressor with my 7mgte compressor head but when i go to slide the compressor on the long stud on the back side it hits the relief valve on the 7mgte head. did you guys encounter this problem? would i just remove the relief valve or remove the stud? dont really want...

curious as to what some people did with their evap system when they did the 2jz swap, not the egr as I know the aristo comes without it. Im going to keep the system so my car doesn't smell like gas with a vented cap. my theory on how to run this would be to run a smaller Charcoal canister, since...

need to know the torque specs for the oil filter bracket bolt to cylinder block for the JDM 2jzgte (RED ARROW). was looking on the spec sheet and found -union for oil cooler x cylinder block (2jz-gte) 29 ft. lbs. - oil filter bracket x cylinder block 65 ft. lbs. so I'm confused to...

doin cam seals on my 2jzgte and i took off the front camsahft cap on intake and exhaust side to slide in the cam seal. my question is, do you have to put a small layer of silicone on the edge of the caps?

just bought my aristo 2jz yesterday and im trying to get the wiring out of the way first and have a couple of questions. here is a pic of the E9 connector and the body plug with the computer: my question is are these the main plugs that normally come with the harness or am I missing the...

i have a rear sump of an sc300 for my 2jz swap and was wondering if i should take it to a machine shop to drill and tap the oil return holes or do it myself. since it is aluminum i dont know if it will react different as compared to metal when doing it. i just dont want the worst case scenario...

looked up some info on using a 2jzge rear sump oil pan on a aristo 2jzgte with a front sump and found that it will work but all you would have to do is drill and tap the turbo drain hole in the ge oil pan. my question is, is that really it because im looking into getting one from a sc300 with...