Search results

I recently switched back to the stock ECU with a VPC/AFC after getting tired of the AEM EMS I had. Now I cannot get the car to idle with my BC264 cams and oversized valves. Are there any tricks to get the idle speed up? It will just stall if the engine speed goes below 1K rpms. BTW, I'm pretty...

Apparently I tightened my stud too far into the head, so I guess it punctred the water jacket. So now I have a serious leak that I cannot stop. I tried RTV, silcone thread sealer, and teflon tape and nothing will seal it. Anyone have any better suggestions?? Thanks.

Need some ideas on why my car is blowing lots of smoke out the tailpipe when I'm boosting heavy. I've had this problem ever since I installed my new 6262 PT billet turbo. I did take the first turbo back, and PT rebuilt it with new seals, but the car continues to smoke a lot (only under heavy...

It's easy to forget how nice our cars were when new. Probably most will never even know.. Here is some high praise for our MK3 supra: http://www.cars.com/go/crp/research.jsp?makeid=47&modelid=437&year=1990&section=reviews

Ok. My dumn question for 2010: Can I reuse my turbo inlet gasket? My original T4 gasket was only used about 50 miles before I took my turbo off and sent it back to PT. I'm ready to get the turbo back, and I'm not sure if I should use a new gasket.

Dynoed on thursday on the local hearbreaker mustang dyno. Before I get to the numbers, this dyno reads 14-16% lower than a dynojet. Final numbers: 431rwhp 401rwt. If you do the math, that's about 495rwhp on a dynojet. This was on 93 octane with 17.5psi and 15 degrees of timing. Plenty...

Does anyone have any information on how to wire up the AEM 3.5 map sensor and the AIT sensor. I did some searching and couldn't find anything about which wire goes where. The AIT sensor has 2 black wires and the Map sensor has a red, green and black wire. Any info is appreciated. I'm trying to...

Alright. My half retarded question of the year: Is it worth it for me to install my AEM EMS or just go with a piggy back like the MAFT-PRO? I bought the AEM used whichh was already tuned. I just don't want to be figuring out for another year how to get this thing running properly. I guess I'm...

Just installed my built 7M-GTE with BC 264 cams.(Still on the stock ECU and AFC). For some reason the car will not idle. It will keep going if I step on the gas, but it will fall into a very rough idle and die. I know there could be lots of things going on, but I went over just about...

Anyone know or have any ideas how I can hook my accordian hose to a 4'' turbo inlet. I'm ready to install my GT35 and I'm going to be sticking with the AFM and accordian hose for just a little while longer. Does anyone sell an adapter? Or will I need to get something from the hardware store? Thanks.

I am stumped on this one. My radiator fan seems like it is spinning to fast after the engine warms up making lots noise when the engine revs up. Sounds like a truck. When I was running the stock radiator, I never had this problem. But then I switched to a CFS radiator and now a fluidine and...

Just saw this. Hope this isn't a re-post. http://cgi.ebay.com/ebaymotors/7mgte-7m-gte-intake-manifold-plenum-Toyota-supra-jza70_W0QQitemZ140141349261QQihZ004QQcategoryZ36474QQrdZ1QQcmdZViewItem

I replaced my badly leaking ebay BOV last night and the car is running stronger than ever. And $60 later I now have 5 gallons of C16 ready to burn. Time to represent.

Just picked up my block from AHM Perfromance. Here's what it consisted of in case any one is intersted in seeing what a typical build involves: Degrease Block......................$114 Align Hone 7 mains...............$302 Mill inline block........................$151 Bore/Plate Hone...

Ran the car at the track for the last time ths year. ITs been a bad year of racing for me. In April I welded my clutch to the flywheel. In September, I ran with horrible track prep and couldn't put down a good time at all. In early November my exhaust studs decided to strip at the last second...

Anyone have a 7M-GTE in the MD area that they want to sell. I'm not really looking for something in great condition, since I'm going to rebuild it with forged internals.

In case anyone missed my thread on supraforums, I put down 511rwhp at 25psi yesturday. Only internal mods are ARP headbolts and cometic headgasket.

Now that I have figured out how to hook my AVCR boost controller to my HKS external wastegate(thanks to Chevyeater and a couple others on Supraforums), I still can't figure out why I'm overboosting. I decided to eliminate my boost controller and just route the vacuum line from the turbo...