Search results

My 7mgte ran fine on AEM EMS V1. I switched over to AEM EMS V2 from Driftmotion. I have the ignition timing set up and appears to be firing like it should. But I have no start. I used a Noid light tester and I have no fuel injector pulse on all 6 injectors. I have a Tweaked wiring harness but my...

I was running my 7mgte on AEM EMS series 1. I had 1zzfe coils and I got it running on that setup. I just upgraded to AEM EMS series 2 (the Driftmotion Honda ECU). Can anyone verify the options I need to make in AEMTuner for COP coils? Under the coils tab I have Coil #1 - On, Leading...

I've probably read dozens of threads on running the 1zz individual coils on aem ems and I can't seem to get a straight answer to my question. Seems to be because there are so many different setups and so many different opinions. I understand the 1zz coils have 12v, ground, trigger. 12v and...

I'm trying to narrow down a problem I'm having with my brakes. I recently redid my engine bay so the brake boost and master cylinder were removed. Everything was reinstalled including a line lock device. The brakes were bleed and rebleed. I had some problems bleeding through the abs actuator but...

A/C on my car has never worked. Back in 2005 I was told it just needed a freon fill by the previous owner. I bought the car with all a/c parts inact. We converted it to R132a and filled it. I could jump the compressor and a/c works. So I replaced / tested every electronic part I could think of...

I need some help. Who has installed a clutch release movement alternation kit? This is required with my clutch, but its not sitting correctly. It seems to be out of center by at least 1/4 inch. Here is the bracket thats out of center. On one end has two bolts that bolt to the bell housing...

As requested, I did a write up on my new -8 (1/2 inch) fuel setup using a Bosch 044 fuel pump and a Walbro 255 fuel pump. I plan to use this to get me to 600rwhp. If you followed my other thread, I hit 540ft-lb torque then ran out of fuel when I got to 5000 rpm. Here is everything you need...

So my previous best was 470rwhp at 24psi on race gas. Since then I added, AEM EMS, 272 BC cams springs and retainers, KSracing intake manifold, 3" piping, q45 tb, 680cc injs (was 550cc), etc. I'm still on my little 61 turbo. So last night I had no problem hitting 471rwhp/417ft-lb on pump...

I'm having some trouble deciding which 7mgte valves are best for me. -Needs to be +1mm over -Good for 7000rpm -Head is fully ported, BC springs & retainers, BC 272 cams I was looking at Ferrea 6000 but HPF website states "Must be used with all other Ferrea valvetrain components" which I...

I'm not new to assembling the 7mgte, but I can't figure this one out. Sometimes I do stupid mistakes and then it dawns on me but here is what I have. I took the head off the motor to install BC springs, retainers and 272 cams. I reinstalled the head with my HKS stopper headgasket with copper...

I'm in the process of doing some custom work around the alternator. For the record I can get the stock altenator to fit but not in an ideal way. I want more clearance in the back. Does anyone know of an alterntor that is not as deep as the stock one? Every millimeter counts. I see there are...

I have the AEM EMS 30-1130 installed on 7mgte with AEM PRO version 3.23.9.189. I set up the throttle and timing. I have added that I am using a AEM 3.5 bar manifold pressure sensor and RC 550 3ohm injectors. You can see my other mods in my signature. I have removed the MAF since I installed the...

From a dead stop, I put the transmission in first gear. 50% of the time it pops out of gear as soon as the clutch touches the flywheel. I re-shift into first and 50% chance of it slipping out again. I always get going after 1-3 attempts. Pain in the ass at red lights. If i put the car in...

I made a post before about my blower fan not working. So far I have replaced the fan motor, resistor, relays, and a/c controls with no luck. After we went over the whole system testing for power, the fan relay is not getting any power. The system works if i power the relay with a wire. Were is...

I searched this topic because I thought this would have been a topic covered many times but I'm not having much luck. And the information that I do find is conflicting. On 93 oct: 7mgte, 440rwhp, 18psi, lexus afm, 550cc, .70 a/r SP61 turbo i shoot for 11.7afr at max psi. I'm on 110oct...

A/C doesn't kick on. Blower fan doesn't kick on. Already replaced: fan resistor, blower motor, a/c controls. Something missing here behind the passenger side panel? (to the right of the green relay) Thanks, Dennis

This is my first attempt ever at making videos. It turned out fantastic. http://www.youtube.com/watch?v=e4yT4zDHPkM http://videos.streetfire.net/video/1990-Supra-Turbo_180505.htm

I just installed a rebuilt head with headwork on my 7mgte and I'm getting some odd compression test numbers on a cold engine: 1. 95 2. 110 3. 118 4. 65 5. 90 6. 122 Now I know your thinking bhg but... 1. HKS stopper headgasket never even fired up, reused, inspected, viton throughly...

Did bad knock sensors/wiring do this to my dyno reading? I street tuned the car, 17psi, 93oct, 11.7afr. It pulled very hard and very fast. The day before I went to the dyno I could feel the power drop. I didn't know what it was on the dyno. No codes on dyno. AFR fell to 10.6 during the power...

I don't post here much but I thought I'd share some pictures of my car I took mostly today. Here is a list of everything I've done the past 12 months. I've been busy. What do you think? 1990 Grand National Black SP61 Turbo Supra Unabridged Modification List: Body: fresh Buick Grand...