Search results

Has any used the Zeitronix Wideband Air/Fuel ratio meter and datalogging system before and if so what are your thoughts about it? I’m looking to spend about $400 for a good wideband for my 7MGTE T70 but I’m not too sure as of right now. Also what about the New Apexi Neon and AEM? Thanks

As my speed increases, the steering wheel starts to shake (left and right). Could it be bad tie rods, ball joints, bushings. etc. Let me know what your thoughs are.

There are two vaccum lines that goes to the power steering. I know one connects from the intake side but where does the other vaccum connects to?

When I turn the Igition to ON, the thermostat needle goes all the way up. This also happens reguardless of what the temperture is. I checked the resistance of the coolant temperture sensor according to the TSRM and it looked withing range. I also check the voltage output and I got about 5...

I just put in a new rebuilt motor & head, new exhuast manifold, wastegate, and turbo on my 89 MK3. I am having some problem starting it up. When I started it up yesterday, it idled real bad and white smoke and oil comeout of the turbo. The down pipe is not fully connected to the exhaust yet...

One of my knock sensor broke off (sensor closes to crank pulley). Is it ok to run on one knock sensor until second one is replaced? Can I use non-turbo knock sensors on turbo engine?

I inspected the vacuum circuit continuity in vsv by Blowing air into the pipe and appling voltage to the terminals. The sensor that connects to the EGR Modular does not by pass the air out therefore it is dead. The other sensor is still good. What problems will occur because of bad vsv...

What size injector is good for supplying a 7mgte engine with 400+hp? I thinking about 660cc. Any inputs?

What brand of spark plug wires is good for producing about 400+ HP? (turbo) There is a lot of brands our there and I just wanted everyone's input. Think about MSD, NGK, and Bosch.

I am in the process of purchasing a rebuilt long block from JIS Engines in TX. Has anyone have any experience with their rebuilt engines? Below is a link to a 7mgt that JIS is rebuilting and is listed on ebay. The 7mgte long block I am getting will have samilar work done to it as listed below...

I purchase a OBX crank pulley and it doesn't have a groove like the stock crank pulley for aligning the crank and cams. How do I go about fixing this problem? Can I line up the key slot of the two pullies and mark the OBX where the grove should be?

I removed the vaccum lines off of the Charcoal canister during my rebuild of my motor. I forgot which vacuum line connects to the Charcoal canister. It would help if some one can send me pictures where all the vaccum lines go. Thanks.

I am think of purchasing a short block with the lower block complete. Can I put a long block Head on a short block or do I need short block head? What are all the same parts or different parts do I need if I am changing from a long block to a short block? Thanks

What is the best over size bore? Would like to produce enough hp to run low 12's. How much hp would be needed to run low 12's? What type of piston and rods would be needed?

Hi, I would like to remove un-need stuff off my supra. I would like to remove the EGR, any un-needed vaccums, hoses, wires, etc.... but need some help on how and what to remove. Let me know what I can remove on my supra. Thanks

What is recommended for a rebuild motor, a JDM motor or a USA motor? How much of a different do the JDM motor make? Would it be better to spend the money I would spend for a JDM motor to rebuild the USA motor? Thanks.

Hi. What can you tell me about determining if a jdm engine is really a jdm motor?

Hi, I have a 7mgte turbo supra and replaced the turbo with a T70. When I try to start up the car, I have some oil coming out of exhaust of the turbo. I know the turbo is good because it's brand new. What do you think might be the problem? The block has new piston, piston rings, and HKS...

Hi, I need to custom a new oil dip stick because I upgraded my turbo to an Ebay T70 kit. I need some ideas on what I should do, maybe what materials to used, what type of angles, etc.... Let me know what your thoughts are. Thanks Joe:biglaugh:

Hi experts, I replaced my battery and than my stock alarm went off. Now I can't start my car, it won't crank and I know it's for sure because of my stock alarm system. This happen to me before and I had to wait a few weeks inorder for my car to reset. Anyone know how to reset the alarm...