Search results

hey guys, got my 1jz in my datsun 260z running and it starts to over heat when it idles for a while. I found out that coolent is not flowing through the radiator when I look through the top of the radiator. The upper rad hose is hot and the lower is cool. Seems the thermostat is not opening. I...

Hey guys, I have my 1jz in my 74' datsun 260z that is just about done. The only issue is that their is no room to run an intake on this car and I basically have the filter mounted on the turbo. My question is that I won't have an intake tube with a fitting to suck out the crank case vapors to...

Almost ready for the road guys. Suspension is finally done, Infinity Q45 lsd, custom control arms, ground control coilovers, new wheels, full poly bushings, new bearings/ balljoints, toyota 4 runner brakes, and CV axel conversion with mosier axels. Fuel setup is done too with a bosch 044 pump...

Just giving you guys an update on the project. It should be running very soon, so we will see what happens!! 1974 Datsun 260z, with a 1jz swap, crower 272 cams, springs/retainers, 60-1 turbo, Drewgo manifold, hks 540's, ect.......Here are some pics-

I am having a very hard time finding a belt for my project car. Its a 1974 260z with a 1jz and I am running no AC or powersteering. I have heard about using the s2000 tensioner pully, but I can't find any more info on what year s2000 tensioner pulley to use, and what belt to use with this setup...

Here are some pics of my new 1jz project. Its a 1974 Datsun 260z. Its the 1jz out of my mk3 supra. Its a single turbo 60-1, with crower cams, hks 540cc injectors, fuel cell, ect. Going to be running a Drewgo manifold and a Driftmotion 60-1 this time around.

Finally got the new setup running. Garrett 60-1, with crower cams, huge intercooler and hks 540cc injectors. The car is running great, but haven't had a chance to take for a spin yet. Going to the dyno in a week or so. Here is a pic.

Just too give you guys a heads up, I work for Nissan and found that the 03-05 exhaust studs for the exhaust manifold and nuts off a Nissan 350z will work great on a 1jz. They are a tiny bit longer but still works fine with my single. They are the right pitch and are easy to get a hold...

I finallly got around to installing my Crower 272 small core cams with Titan cam gears into my 1jz, and my new intercooler. Shimming the cams in the car was a bitch and a half! Big thanks to Zazzn for getting me the cams. Hope to have it at the dyno soon! Here are a few pics-

I'm installing cams into my 1jz and I was wondering if anyone knows the factory spec on the camshaft cap torque in" in-lbs."

My Boss at work was looking at my supra and was telling me that if I got pulled over and they looked at my engine then they could impound the car because it is not stock. I think he is full of it, but I don't know. I know they can give you a ticket, but I didn't know that they can impound the...

Well I just installed a set of JDM 440cc injectors and everything went good. The only weird thing is that on my low throttle and idle settings on my AFC, I started out with a -15% the car was running lean and crappy, so I zeroed out the afc and now it runs great (14.7). I am running a 10.1 AFR...

I am just curious. I got my car with a 7mgte, R154 in it, but now I have a 1jz swap. I was wondering, because my gauge cluster doesn't have a factory boost gauge on it, but it has the factory boost sensor to operate the gauge in the dash? Do I have an NA cluster in my car, possibly my car used...

Well I have an oil leak that is decently bad the is coming from what looks like around the bellhousing. It is definitely engine oil and not tranny fluid. When I did my swap, I resealed the oil pan and replaced the rear main seal perfectly without putting a knick in the shaft or putting in the...

Whats up, Does anyone know a good ECU pin that supplies 5v that I can tap off of for the boost sensor reference voltage for the Zeitronix wideband?

Here are a few pics of my Supra now that I finally got some decent wheels and suspension. I am currently editing some cool videos that I will post up too. http://i176.photobucket.com/albums/w178/timbo1j/IMG_0784.jpg http://i176.photobucket.com/albums/w178/timbo1j/IMG_0783.jpg...

I just got an adjustable fuel pressure regulator kit and I was wondering what the stock base fuel pressure is on a 1j with the vacuum line off??

Just wondering what you guys think. When ever my car is running the hydrofan is always spinning pretty fast. From the second I turn on the car the fan speed does not change. The car does not get hot at all, it actually runs very cool but I know that the fan is supposed to very speeds depending...

Just wondering how I can tell if my 88 Supra is an out of state car or a California car. Is their a way to check by the Vin #?

Whats up guys, When I removed my 1jz from the front clip that I got, I found that the motor mounts are completely shot. Anyone know where I can score a set of 89+ round style mounts because I haven't been able to find them anywhere?