Search results

I just finished redoing the intake manifold gaskets on the 7mgte and replacing the accordian with a harpipe and running intercooler hardpipes.. it's just under construction but here are some pics.. it's a bit messy. Anyway it runs really good now with the new in tune tps and hard pipes etc...

ok thanks. Also i just got the engine running. I know the engine is a 1/4 quart overful. So i'm gonna drain that out. But also is it normal to smoke from the exhaust? it's just like cold weather smoke though but it was consistant. Also it smelled like carbon or fuel.. one of the two. The...

Where do i plug the boost gauge hose in at? Is there any specially particular place for that supposed "ground" should go. Again, calling that a ground is an educated guess. What is that wire that comes off the coil pack?? Again sorry for my vague question, i'm tired.

***The clear hose routes to the dash where the boost gauge is...

I think i managed to do it with the digital. I tuned it until it supposedly deflects. Where it goes to the highest resistance then it'll go to nothing so i turned it back to that fine line before the highest resistance and nothing. It's hard to explain but i believe i tuned it correctly. I...

what ohm setting on the multimeter do i set it to?

How do i get my ohm meter to deflect? I forgot how to tune the tps. I used to know how to but it's been so long.

well originally my wanted ad was for non tems but Tubbie said that the tems struts on a non tems car is actually better since they can be adjusted from the top with pliers. Is this correct? So i got a good deal, and i took it. I just installed them as-is after a brief look over. I don't know...

I installed them correctly. I did adjust anything with the spring tension bolt.. Is that what it's called? So how would i go about making them harder? or are they just worn out a bit? My friends 04' ION has harder suspension... it doesn't bounce as much when u press down on the hood or trunk...

Hi i just put on some tems struts on my non tems 89 turbo supra and i wanted to know how to properly tighten them? they're real loose and bouncy. I wonder if i use a rachet to tighten down the bolt on top of the strut or theres a little thing in the middle of the strut. Please help...

If one is missing a filter. what should i do? cap it off or leave it?

Hi i can't figure out what vsv goes where on my 7mgte since ones missing something from what the tsrm shows and i just can't figure it out... Here just Tell me what Number vsv goes to what number on the vsv tsrm diagram.

Do i mount the vaccum tree on the upper before installation of the upper? or do i install it after the upper is installed... It would be a PITA to install it while the upper is installed..

sounds good. I'de actually look into that. PM me a pic and paypal address...

Ok so I pulled the intake manifold off to replace all the hoses and gaskets to prevent leaks for best performance. So as we were pulling the harness after everything there's a wire that runs down to the transmission that has 2 wires... I couldn't find a connector though? So i cut it to remove...

But if the ecu is usdm then i'de still have to have the egr on it to work properly, right? the egr wasn't needed on the jdm spec ecu specificly, correct?

ok so this is a usdm engine. Unless the installed a usdm upper end and used the usdm ecu that came with the car. Anyway has anyone ran their usdm without egr with stock setup? stock boost etc? thanks

Hi i was just wondering what i need to get from the motor to see if it's really a jdm engine. I was thinking i could get the engine code (where ever that might be). And just post a pic up here and see if u guy's can tell me about the car... THANKS

I'm not sure of what to look for on ebay. I can't find a turbo afm adapter on ebay. I'm talking about the adapter alone. Could u help me find one? Thank you