My son picked up a MKII that's set up for a 1jz that we're building for his first car. The PO blew the HG and only the bottom end remains in the car and since my son's footing the bill the budget is tight so we're looking at using a spare 2jzge I have in the garage vs. buying another 1jz (mom...
Hey guys, in the process of rebuilding my R154 and am having issues figuring out if I have the output shaft center bearing in far enough. Can anyone tell me what I should be measuring between to check the 1st gear thrust clearance?
I'm measuring around .73mm between the inner bearing race...
Was on my way to work this morning with the E/T streets on the car (was planning a trip to the strip tomorrow night) and heard a loud bang during a 2nd gear pull and now I've got a loud rpm-based clanking that goes away when I push the clutch in.
I know the 1st gear thrust washer is a weak...
Trying to chase down a no-run condition w/code 14 and I figured out that cyls #1 and 6 (1st coil pack) are not getting spark. I've checked continuity in the coil pack harness and between the igniter and coils and all checks out ok. I've tried my spare ECU and also tried swapping coils and a...
Been DDing my MKIII for the past couple of months and have had a couple of instances of what I think may be vapor lock--car won't start (or starts and barely idles) after driving for a while in our lovely 100+ degree temps (30+mins) and then sitting for 15-20 mins. Both times this happened I...
I recently put together an RX7 oil cooler setup using Summit -10 (5/8") Twist Tite hose and their fittings. A few weeks later one of the hoses popped off my remote filter mount, spilling 5qts of expensive synthetic on the road but fortunately not toasting my motor thanks to oil that got blown...
Started disassembly of my diff to replace the crush sleeve with a solid spacer and hopefully get rid of the driveline play but I don't have the SST to remove the front pinion bearing or crush sleeve.
Anyone find a solution other than the SST to get the bearing out? Tx2k10 is looming and I...
Not really the time of year to dyno (90 degree temps at 8AM with 80% humidity), but I wanted to get some closure on one project before my buddies talk me into putting an LS1 in the 1970 Valiant I bought a few weeks ago...
By doksurf33
Video: http://www.youtube.com/watch?v=kSMFGmMleyw...
Sorry in advance for the novel....Troubleshooting a lean condition about 5500rpms on my 2jz NA-T and was hoping I could get some suggestions. I'm running 7MGTE electronics with the Lex AFM/SAFC combo.
My fuel system is fairly overbuilt as I'm running E85-I have a walbro in-tank feeding a 2...
Been looking for a 2wd Yota truck for quite a while so that I can sell my 4-Runner and Escort and have 1 vehicle that I can haul stuff in and gets decent gas mileage.
Unfortunately they're impossible to find down here because everything under $2k goes to Mexico. Ran across this today for...
Post 'em up!!
My GF took most of the pics (she's gonna upload at work tomorrow), here's the few that I took with my camera:
Custom battery tie-down, thanks for the help Jay and Keylan
Picked this up the other day, has kept me from working on the Supra aside from tonight :)
2007 Hyosung GT650r that was dropped at low speed (hence the lack of fairings), picked it up for $1800! Going the streetfighter route, so a few repair parts and some paint and she'll be good...
Been playin the o-ring game for a few weeks now and figured I'd share. For anyone looking to fit domestic injectors in the 2jzge fuel rail (or 7M rail for that matter), you need McMaster Carr PN9263K696. This is a 7mm ID, 2.5mm thick Viton o-ring with a 12mm OD. I pressure tested these up to...
I'm having issues with my car running pretty lean at idle/cruise (17-19:1), probably due to the 680s and E85 (720s would have been a better fit but I got the 680s cheap) and I'm getting some surging at low throttle. I've got the base FP at 45psi with the vac line off, any more pressure doesn't...
So I have a 2jzge NA-T but I'm running it on the 7MGTE ECU (hence posting in this section) so troubleshooting ignition should be the same. I'm running 12psi with a T70 right now and am having issues with ignition breakup from 5500rpms up.
I regapped the plugs to .022 and it helped some but...
Figured some of you Aussies might be participating, I'm growin some mean handlebars myself :thumbup:
By doksurf33
For anyone that hasn't heard of Movember (http://www.movember.com/), It's an annual worldwide charity event that benefits men's health . " Mo" is Australian for mustache (you...
Full story and specs in my build thread (link in my sig), stay tuned for more payoff vids:naughty:
Edit-Director's cut with commentary: http://www.youtube.com/watch?v=C8vj6x7eMuQ
Went out and had some fun today:
In-car 1-3 Pull: http://www.youtube.com/watch?v=f06dK5Y1jfo
1-3 Pull from...
Had a blast as always this weekend, even more so since I was is my Supra for the first time!
I'll start it off, let's see some pics/videos!
Fudd's meetup on Saturday
Chillin' at Lance's fixing Johnny's car while he watched :biglaugh:
The 2j powered Maverick
Buck-toothed Miata
2j...
Haven't seen anything on this car here (mods can delete if it's posted somewhere), pretty badass:
http://www.homemadeturbo.com/forum/index.php?topic=95851.0
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.