Search results

Hey guys, Im making some posts trying to get this swap done with. i am putting in a Jdm 2JZ GTE in to my 89Mk3. I previously had the 7m. and my heater core was leaking, so i bypassed the heater core altogether by looping the coolant line back in to the block. I am trying to do the equivalent...

Hey guys. I did the head gasket not too long ago, all went well. Now literally minutes before the problem started, represented by the video as an example, it was on, idling for 20 min Perfectly. I mean idle, temperature, mechanically she was fine, or appeared to be. No symptoms at all, no odd...

Hey guys, as the tittle states, im looking for a new turbo and came across this one. spes: GT4082 Compressor Specs: Wheel Diameter: Inducer: 58.0mm Exducer: 82.0mm Trim: 50 A/R: 0.58 GT4082 Turbine Specs: Wheel Diameter: 77mm Trim: 73 A/R: 1.24 Type: Free Float has a high...

I have now gone through my third r154 in my mk3 @ 700 whp. i know a stock tranny will never hold up to that power, and i intend on getting more. i have made a thread in the past for some suggestions if I should stick with the r154 or go for the gtrag. now i am just looking for some advice on...

I just did the HG on my car, hooked everything back up and when i attempt to start her up she is leaking water (not using coolant) out of the exhaust pipe, and i can see water leaking from the rear of the engine by the exhaust manifold just south of cylinder six. I had my mechanic look at it...

Here is the scenario. this is for my friend. He has an 90supra with a 2jz in it, holset 40(spelling) turbo, with 1000cc, intercooler, aem ecu, hks sssq bov, dual walbro 255’s, fpr, 50mm hks waste gate. he is currently making 650+ WHP @ 26 psi. Here is the issue. He has a 6 puck feramic...

I made a post in the wrong forum section, so ill just copy and past eit in there, with the replies too. my friend has an 87 mk3 an di just did a 2jz gte swap in her. he is running rich and i don’t know why. his wideband shows at idle, 14.8, WOT = 10’s, 100km/h = 14.8. It has intake done...

Hey guys. my friend has an 87 mk3 an di just did a 2jz gte swap in her. he is running rich and i don’t know why. his wideband shows at idle, 14.8, WOT = 10’s, 100km/h = 14.8. It has intake done with three inch piping, stock twins running around 14 psi, 3inch exhaust, walbro fuel pump...

as the title suggests i have a 4.3 lsd in my 89 - gte/r154 . Now i look at the tsrm and it shows the oil pressure standards should be between 2.5 kg – 5.kg/cm3 @ 3000RPm My question is, because now i have a different rpm ratio than stock, and now that my rpm per km is higher, do i apply the...

Before i ask my question, i tried doing a search because i know i have seen this topic discussed here before, but i am on page six in the search engine, and less i overlooked it, i can’t see anything. I know someone who is selling 6 550 Hi Impedance injectors(TII) for 160. Now, my question...

So I took my 89 turbo supra to the dyno (mustang dyno) today for the first time. I’m pretty pleased with the results. under the hood my mod’s are full three inch exhaust from the elbow back, with no cat, intake, and a MBC. I am running with the LSD 4.3 Diff. I don’t know how...

Ok guys. I have what I believe is the dreaded rod knock. I have watched other member’s videos posted with their rod knocks and my sound is very similar to theirs. I am not the greatest engine expert, but a rod knock is from the lower end of the car yet the sound is (well at least to me)...

http://videos.streetfire.net/video/12e21c4e-2ccf-4f0f-bf15-99a100ea29a8.htm not sure how old this video is, or if it was posted. I got it form street fire. Nice run............... :) PEace..........

Hey guys, long time viewer first time poster. I Just did a N/A to Turbo swap.(turbo engine/tranny in to a N/A car.) And I decide to keep the N/A diff with LSD. I still have the Turbo diff, perhaps ill swap it in one day. The car runs, but needs a complete exhaust, so I have not really driven her...