Search results

Bump. Any updates?

Blown away! Had no clue this was available. Thank you!

BUMP... I'm having to re-take a look at my rewire work from 7 years ago... I am in disbelief of how simple this looks to be, to accomplish the mod (Canadian running lights). Basically keeping on the fog circuit, Canadian trim. What gives? Has anyone done this mod, by just re-pinning or...

U can also tone it out or trace, to make sure you have the right signal identified. For instance, below is where the reverse light signals should terminate on the harness (to the MKIII dash). M1 PLUG: Pin #1 R/B wired to W at tranny connector (Reverse lights). Pin #2 Y wired to B at tranny...

Anything? Anyone?

Is this all that I'd need to do this mod? I want the sleepy-eye look, with full brightness/benefits, etc. If I fab up a housing like this, and put where the reg sealed beam goes, is that it? Please LMK the specific "basic" steps to doing it this way... 1. Acquire _____ headlights (source)...

U can run w/o the cam cover, however, there is an o-ring in the intake cam gear, which could leak (slingin' oil all over your engine bay). I have a spare front/cam gear cover somewhere (email me g099521@yahoo.com). The valve covers should be easy enough to find on Craiglist for cheap.

Like said earlier... verify the TPS wiring to the ECU (tone it out) to make sure that they are not backwards (which is equal to the 100% open).

The metal sleeves are 2-piece, so just cut/break the rubber in between. I tapped a flathead all the way thru the bushing and it loosened enough to tap the whole thing out. If I remember right, there's a lip on the metal so you have to tap them out from the bottom maybe. Been awhile (never...

The only diff I know of is w/the amperage, NAs compared to a 2JZ-GTE. NAs should be the same and as long as the harness connector fits (round or oval), they are interchangeable. Can't remember which one, but there's a 10A difference I think. Good luck.

I am putting an SC300 engine/harness into an MKIII. Do you have the wiring map for what you did for all the dash connections/signals? The harness and dash connectors are very similar (tho I plan to keep my SC400 intact).

I removed the STA pin/signal in my 2J swap. Can't remember exactly why we found I didn't need it, but should not be the cause of your 4K RPM limit issue.

I used STD bearings and ended up spinning #6. Maybe not because of the size I chose, but I shoulda just gone with the #s on the block/rod/crank, like the TRSM tells you to. On another build, I used .025 over and that's one's strong... I'm assuming because having the crank turned made the...

You may be able to use a resistor or sumthin', if you're weather/temp is consistent... It what we do w/MAF/VSV signals, etc., with piggybacks.

I have all of this on hand and various Lexus VVTi diagrams available. Going into the GF's 1991 GE/auto. Been awhile since I collected parts and did my swap, so just making sure I don't get into the middle of this and end up stuck. What else do I need to physically install and be turn-key...

Just "scattered notes: B1 Pin 4 is for the FP signal, which would go to the Aristo's big plug (#29 in the diagram on post #42). That plug is really 4 subconnectors C, D, E, & F. The C connector (pin 15) within that plug is the same thing. Goes to the diag box. I removed the diag box and...

I am going to use the 1JZ auto, w/2JZ-GE engine/harness/ECU. I'd like to have the 2JZ ecu control the tranny (30-41LE, or A341) and it has the provision for mechanical speedo cable. Do any of you already have something documented/complete for this.

Cleaning up my sites/routines and this is one of 'em that's gonna get gone for a bit (won't be visiting often)... Gotta get a hold of me? My old friends or contacts, or for updates (Pics/threads/write ups), just let me know. Satan's contact info: Email G099521@yahoo.com...

I think I also included some pics/write-up in Ronnie's thread before. LMK if pics don't show up and I'll rehost. Good luck!!

^^Thanks for your technical contributions. A post, to talk about another post, in a thread you were not already a part of. Smart. We need your superiority here! Welcome to the new Supraforums Off Topic section. I just "brought a friend" to the thread, to show him the "stock" circuit and...