Search results

Hey guys, I just started to get my 91 turbo back up and running and I noticed after I changed the oil pressure sender that my Oil pressure gauge is pegged as soon as the car gets started. I am trying to figure out the issue, but my Haynes manual doesn't mention this at all and all of my...

Hey guys I have spent a little bit of time looking, but haven't found much to go on and I am terrible at reading wiring diagrams. 12v IGN wire in the engine bay that I can use as a signal wire for a secondary fuse block that I plan on wiring all of my accessories to as well as may be an electric...

Hey guys, it has been forever since I have been on and I'm sorry for that, life got in the way. But now I'm moving and I have to finish my supra so I can move it. While wrenching I came across this plug that I have no idea where it goes. Also, does anyone have any ideas of an oil leak turbo...

What is this threaded hole near the block side of the pcv vent tube. There is nothing in mine, should I find a bolt and plug it. What is it?

I came into and aeromotive 13301 afpr a while back and everyone advertises it as needing 100 to 250 a gallon per hour fuel pump. I have a walbro 255 lph fuel pump and that comes out to about 60 gallons per hour that's nowhere near the 100 that I would need. When I was looking at Walbro 400 lph...

I plan on running a map ecu, and I was wondering if I would be able to use the 12v ignition source for the ecu to power the map ecu as well as my wideband or if it would put too much load on the circuit? I'm not an EE and was hoping to hear from all of your experiences and know why it would or...

I have some pig tails for some PTE 550cc injectors and I wanted to know the part number for the male half of the injector connectors so I could make a plug and play harness so I don't have to cut the original harness. I know Supra sport sells a PnP harness for their FIC injectors, so I just want...

I have a question for you guys, I searched the boards and couldn't find a similar setup to what I'm looking at doing. I was wondering how far I can push the stock fueling on around 10psi. I currently have a GReddy ProfecB-II for my boost controller, a 57ct and a cone filter (on a freshly rebuilt...

I'm looking to piece an exhaust together on a budget all 3" of course, I know I want a vibrant 1149 and two resonators, it looks like $250 so far with just the resonators and muffler and I want this to come in under $400 total. I'm wondering how much straight pipe I'm going to need, I was...

I have been searching through the forum for a thread that compiles all of the different options for aftermarket intercoolers and piping kits for the mk3 in general, and couldn't find any. I was hoping that we could use this thread to compile data on all of the options out there. An intercooler...

I was having problems with my heatercore, those have been fixed and the dash is back in. Like with every project I start, I do my best to take lots of pictures and label everything, but it seems like I always have problems with the stuff I forget to take pictures of and this time it is the...

I got a new diff, but before it goes in my car I'm going to clean it up (Wire brush and some paint, no big deal), but I need a gasket for the cover. I was on the interwebs and came across the FEL-PRO Part # RDS55431 which rock auto says is for our diffs. Have you guys used or seen one of these...

So I was doing a random walk around and fluid check on my car today. While checking my coolant reservoir it was right below the full line, so it wasn't a big deal in my mind. But then I checked the radiator and found that upper part of the radiator was empty and so was the upper hose, so I did...

I bought some bulbs today that Silvania says works in our fog lamps, but I got under the car and the fogs are sealed like the headlights, does anyone know the part number for new fixtures or am I just crazy and should actually be able to swap out the bulbs. Silvania said that what I needed was...

Hey ladies and gents, its that time of year again for the greatest college race in history. I of course am talking about the Purdue Grand Prix, and along with this amazing race the Purdue Automotive Performance Association (PAPA) is holding its annual Grand Prix car show. I would love to see all...

I have a question, where in the heck can I find a quality LSD/ Differential rebuilt kit. I'll probably need bearing, shims, clutch discs, seals, the whole works, and I might even need a new gear set. I've scoured the forum, and there may be a second option of going with a TT-R gear and torsen...

What could cause your speedo to go out. I put in a brand new lower cable in Nov., and just now on my way home my speedo stopped working again. The first time it stopped working i thought it was due to the fact that the cable was 20yrs old, but now I'm wondering WTF this thing is brand freakin new.

I just noticed today that my car at speeds over 20mph about the car vibrates really bad steering column included. Before recently I would get similar vibration when I was off throttle or braking, but now its happening all of the time. Has this happened to anyone before, could it be the tie rods...

I'm looking for the updated ignition clips. they look like these pictures. I'm trying to amass a number of these so I don't have to worry about screwing up re-pinning them for my IS300 ignition mod. I'm just looking for a part number so I can put a bunch on order at my local Toyota dealer. Sorry...

I have heard that some guys have gotten smaller charcoal canisters that work, but I have found no one who could tell me where to get one. I would really like to put a catch can where my charcoal can is, but I won't do that until I have secured a charcoal can that is smaller so I can hide it...