Search results

Sounds to me like it can be your starter relay. It is located on the passenger side kick panel. It happened to me also, by the way how old is your starter?

Yeah i took it o autozone and they only checked the voltage and it was 14.xx . I talked to the person the techat Eagle Electric and he told me that it didnt matter how small or big the shell looked. It was the insides that count because all they do is re-wound them to 130 or 160 and install our...

Man i im the market for a clutch and i was looking at the ECLUTCHMASTERS STAGE 2 for 7mgte. I claims to have a 2800 lbs of clamping force and its good for 490 rwtq. Im gonna look for a clutch shop here in houston and im gonna but this clutch to see it it actually has 2800 lbs of pressure . The...

Anybody know what can i use to check the amps of the alternator to make sure its a 130???

Yeah that z06 must have been all stock or else he would have killed me at my 9psi . I found the boost leak that made my car fuel cut at the end, it was the vacume line that goes from my HKS EVC EZ Silenoid to the wastegate. I found some zip ties and got it taken care of. I got a crappy phone...

Just dont give up on your car man, its got power. All it needs its a lil work . Check out the kills section . 1st day with car running and im already killin domestics AAAAAAwwwhhhh the beauty of it :evil2: good luck

How do can i find out the amps of my alternator? I bought a 130 amp but it seems to be smaller than what i got. Any help would be appreciated thanks oscar

Well i just got my motor put together yesterday(saturday) and i got the supra running good. It all checks out good, so today i went to a friends shop here in houston (MEXICO) : ) and a 300zx twin turbo is trying to play with me. Hes doing a couple of pulls besides me and im like fuck it lets...

Not bad at all man. You know what , I could never get my MBC to hold boost. It could be something as small as a boost leak or wastegate not working properly. Good number man, find that problem and take it to the dyno again...

Thank you very much to both of you guys for the info.

Guys i have been searching for the picture of the install pic of the cps for 30 minutes anybody have link to it. thanks oscar

Guys dont kill me if it has already been posted, but AUTOZONE has the CASTROL SYNTEC ON SPECIAL...:aigo:. The special consists of 5 Quarts of Castron Syntec (hhhmmm 0-30w) and a K&N $15 oil filter for 27.99. Just though i would let the community know about it and no i dont work for AUTOZONE...

Yeah they are the Red High Imp 550s cause i have the Tan Low Imp 550 Injectors form the 87-88 Turbo II rx7....:icon_bigg

Im planning on running the CRX RACING new aluminum radiator with it and installing a temp controller so i can control both speeds of the fan. I seen the 2nd speed on the damn fan and GOOD DAMN does it flow some air. It pulls some amps though like 30 i heard, thats why im upgrading the...

HI everybody , the alternator im talking about is the ones from ebay. I called 2 shops and the 130 is an mr2 alt with a mk3 round plug. The 160amp is a rewound mr2 and they both come with a 1 year waranty. Im just gonna go with the 130 amp cause its anly 50 amps bigger. Im gonna run the taurus...

Guys im in the middle of a decision, wether to get a 130 amp alternator for 85 shipped or a 160amp for 150 shipped. What do you guys think ? Will the 130 be fine for some E-fans and some other electronics?

Yeah!!! I agree with those number being TOO low. I did 355rwhp and 377rwtq at 11-12 psi with stock intercooler and injectors. And my car did 377rwhp and over 400rwtq at 15 psi but back it down, it was too lean for me. Do you have an aftermarket boost guage? It will tell you if you have vac...

Im rebuilding my 7mgte engine and with eagle rods and Probe pistons for a 500 rwhp DD . Is it Necessary to balance the assembly? I running into money issues, anybody done some good power with out balancing the rotating assembly? Any input is always appreciated

Good to hear you didnt sell your car man. Hey did you have your rotating assembly balanced? Im goin with a eagle rod probe piston combo and was wondering if i needed to balance the rotating assembly. Aiming for 500rwhp daily and 600rwhp with race gas etc through a master power t67. Keep us...

Thank you guys, I found some at Ace Hardware . They didnt have the brown grade 8 ones though, only had standard sizes on those.