Search results

  1. lilmartian09

    Here is a challenge. Front window fog

    Hey everyone. Been awhile since i asked a question but maybe some insight will help. Have any idea as to why the window has a light blue fog on the windsheild. I know its dirty but what is it. I don't use the heater or ac. Thanks again Sent from my SM-G920P using Tapatalk
  2. lilmartian09

    Turbo A Oil Pan?

    Does it exist. Supposedly it does and looks like this. I need a new oil pan. Badly. I would prefer this one because of how thick the metal is and the sealing part. Sent from my HTC0P3P7 using Tapatalk
  3. lilmartian09

    Idle problems 7mgte AEM V2 ecu driftmotion

    Here is the delima. Ive finally got it to turn on and run. My problem is that it doesn't stay on running. Ive tried adjusting the fuel to see if its that and its not. It should keep on running from my understanding once it goes. Ive checked everything and am not sure where to look anymore. Any...
  4. lilmartian09

    MK4 Supra Wheels

    What is the difference between NA & TT wheels. If anyone has original size as well it would help.
  5. lilmartian09

    Rear Sub Frame Upgrade

    So here is what happened. My sub frame has a small crack. Not fully broke yet. I need some suggestions as to what I should do. If I get another frame it will crack. I have over 300whp and I dont want it to snap again. Is there any way to fix this or send to someone who can upgrade and repair...
  6. lilmartian09

    Cam Sensor Alternatives. 7mgte

    Has anyone ever tried to remove cps and replace with a newer type of sensor. What mods where needed and if you needed to change computer who did you go with. No problems with mine just want to see what has been done. Duane supra is a perfect example. Any other choices?
  7. lilmartian09

    Loop Idle Problem

    Have a loop idle. All the vacuuming is good. IAC is good. Here is the problem. If I fill up with full tank it does the loop idle. But if it's at or under the 1st quarter tank it idled fine. I am missing my 02 sensor, heater bypass valve and my fuel vapor canister. I ran the fuel vapor straight...
  8. lilmartian09

    Need help finding short

    As the title says I have a short. Here is what happened. I just finished rebuilding the engine and installed like the usual. Hooked up everything as it was before. My problem is when I hooked up the battery to get it started it turned on my dash lights. It shows the CEL ebrake door light battery...
  9. lilmartian09

    El Paso Supras (EP Supras)

    First Pictured Meet:: Turned Out Pretty Well. Location Was At The Cars & Coffee Meet. Few MK4s. 2 MK3s & 1 Cressy With A 2J.:evil2: You Can Hit Up Me Or Suprajr To Kick It.
  10. lilmartian09

    Storing?

    Okay so basically I want to store my motor until I find another shell. The current shell that I have is having some really bad electrical issues that just keeps on going. Starting with the common taillight issues and now my heater is starting to go out and im not up to replace the dash and the...
  11. lilmartian09

    Wiring es250 fogs

    Need some help with the bulbs that i got. They are the H3c bulbs and im trying to figure why it wont turn on. I know it has two connections on the back of the bulb. I figured from the lexus I took them off that one of those connections is a ground and the other a positive. So I tried wiring them...
  12. lilmartian09

    Need some inputs

    Okay so here is wat my issue is. Taillight circuit which turns on dash, side markers and tails is being controlled with brake light circuit. Here is wat I have found out so far. Using this...
  13. lilmartian09

    Brake lights problem

    Okay so here is what is going on. Basically everytime when I brake the dome lights and side markers all turn on. If I turn my dome lights on by the switch on the steering wheel dome lights and side markers turn on but when I brake no brake lights turn on. Here is what I have done so far all...
  14. lilmartian09

    Intermediate Steering Shaft Help

    Im trying to drop my sub frame to replace oil pan seal and the intermediate shaft is stuck. It came off before. I did remove the bolt that holds it in place but still nothing. Also tried to wiggle it out. Anyone that knows a trick to remove it please tell.
  15. lilmartian09

    Howling Noise

    While im driving normally around 2k rpm the car starts to make this howling noise. Intake and intercooler is all stock except the air filter & I have the bosch BOV. When I lift off the throttle it kinda makes this short release of pressure but it sounds ugly. I wish I could get a vid but I dont...
  16. lilmartian09

    Cant find missfire need some help

    Okay here is what happining. Fresh motor with a 1mm oversize pistons. All new. I only just started it and only put 3 miles on the motor already. Im pretty sure I still have to seat the rings but I dont think it should be missing like it does. All spark plugs,wires, and coil packs are good. CPS...
  17. lilmartian09

    Need Help Reading Ohm Device

    Im having trouble on how to read this device. In the TSRM to check AFM it said to see how much resistance the AFM putting out http://www.cygnusx1.net/Supra/Library/TSRM/MK3/manual.aspx?S=FI&P=96. Now I did find out. It told me .956 under the 2K selection of the ohm reader. So my question is how...
  18. lilmartian09

    Fuel Pump Help

    I need some help everyone. Here is the story. I just finished rebuilding my 7mgte and finished installing everything but now I have a issue. I turn the key on and everything has the same noises letting me know that those things are turning on except the fuel pump. As I jump FP +b the pump turns...
  19. lilmartian09

    Breaking In Motor Theory

    I read an article about breaking in motors and having the piston rings seal really well with this motousa or motoman. I read his theory and I really want to do this as I am building a 7m with forged pistons and the whole 9 yards with the block as machining, balancing and some other things that I...
  20. lilmartian09

    02 Sensor Thread Tap & Die

    Anyone know which Tap & Die set i should get. The AEM UEGO comes with a Bosch LSU 4.2 and the size for it is M18x1.5. The thread is going in BIC Divorced Downpipe its this one not shiny tho