Search results

I am talking with this guy about buying his EMU off him. It comes with harness and 3 bar map sensor. The above quote is out a PM. My question is will this Y001 map sensor work with the emanage ultimate or just EMB? Thanks.

It's been running fine with a slit misfire going on. Been driving it only 1.5 weeks 30 minutes a day... may be. Yesterday it out of no where, I start it and the idle is dipping and coming back a lil. By the time I get 50 ft from the house, it's dipping bad. I hobble back to my friend's house and...

This is a 2JZGTE with a T60-1 and USDM 550s hooked up to a 7M resistor pack. It is also living in a 91 toyota cressida, which very similar to the MK3 supra. I try and crank it (sounds like it is only catching a few cylinders) but it takes some tries. I've got to peg the gas so when it finally...

Little background... This is my first build and first time turning wrenches on my own. I had help over the phone on the wiring and I've gotten my car to crank and run here's my shitty but awesome to me crank vid... After that it crank and idled fine. An oddity was the temp sensor always went...

I picked these up right quick of SF. I am not sure if it is excessive to the point that the timing belt would slip. I am kind of annoyed, but it was an impulse buy so I had it coming I guess. Now I know why they only show the front and back in all the 4 sale threads I have ever seen. Thanks...

Okay, after 900 years, a claim, 20+ emails, and finally realizing that they just might be out $1K, RHDjapan.com started trying to explain why they say "it'll work". That phrase so untrustworthy from companies that I just could never install a ghetto rigged clutch in my car and cross my fingers...

I just got off the phone with Justin over at Spec. He couldn't give me a definite date for when it is coming out but it's first coming for the 7MGTE/R154 then the 1JZ/R154. He actually clarified that the 7M flywheel is actually thinner than the 1JZ. Other than that the FW and cltuch assemblies...

I was wondering if I need a different rail to run low imp injectors on my JDM 2JZ. I know that I need a resistor pack from the 7MGTE. I guess along with that question, what about injector clips. . . I kinda don't know what they look like or care what they are unless I some how need them to run...

Hey guys, Does anyone recommend a recirculating/plumb back valve? I had a SARD R2D2 BOV but decided that I wanted the power to be as incognito as possible unless I am leaving them by many car lengths. Also, I've been told since my JDM 2JZ lacks the door flapper, I can run whatever and my A/R...

Hey guys, I got my HKS GDmax clutch kit and noticed that it weighed the same if not more than the stock R154 assembly. I'll throw some pics up later, but for I word it the best I can. The flywheel seems to be unnecessarily thick, especially toward the outside. I was wondering if it was possible...

I have seen plenty of avatars with peoples cat it them. Wanna find out if there is a pattern here . . .

Hey guys, I am kinda chasign my tail trying figure out what is going wrong with my drive shaft situation. First off, in the world of Cressida's doing a manual swap is a genuine bolt on occasion. It all bolts up just like it would in a MK3 (save widening the tunel for the R154). We use the MA70...

Sup People, I have been a little concerned about my motor lately as I get closer to completing the swap. I was trying to turn the crank the other day to put on a flywheel. The first few turns seemed more difficult than I had previously had done. After several turns, it was fine again. This is...

I was wondering if the 2JZ oil filter threading is the same as the 7M threading . . . 3/4 inch 16 thread. Cuz I was reading this thread and thought to myself "Gee, that's really cheap and effective and even almost necessary for a turbo car. "...

I need help translating .. . yes, I have try babelfish and others. It still leaves me hanging. I did a screen shot of what I need translated. Here's the link as well if you would rather that http://www.rinkya.com/twview.pl?URL=http://page19.auctions.yahoo.co.jp/jp/auction/x9047567...

Hey people I am going to purchase a carbon twin clutch for my 2J/R154 setup. I was just going to purchase it new $1600, but a used one came up for $700. The disc are very glazed. How much does a set of replacement discs run for this clutch? I figure the pricing for the 1J and 2J clutch discs...

Hey people! I was looking into a cheap upgraded fuel pump. I can get a mk4 tt pump for under a 100 shipped. I heard/read that they can hold my planned 500hp .. . I think I need to bump the volts up with a resistor (stock 12, needs 13.5-14). Anyway, my question is whether or not fuel pumps...

I know people replace the JDM twins with steel turbos. I need a set for my JDM 2JZ twins. . . they are just a tad big/different than USDM twins. Can someone give me a link, name, number, etc. ? Cheers, Jago

Sup people, second post but PM alot . . . mostly for the classifieds. I got a couple of questions about stock JZA70 JDM torsens. 1 can you swap out the center/ring thingy? I have a 3.9 open diff, and it is a 4.1. 2 what is a fair price for one in good condition? Thanks, Jago

Sup people, I own a 1991 Cressida. Since our cars are related, I will be poping in for some sales and purchases and parts questions (try not to flame me though). Anyway, the link in my sig is to my build thread. . . nothing exciting yet just engine refresh and parts hunting rants :cry: . . ...