Search results

  1. I

    1.5JZ + Standlone - Batch spark/fuel or Sequential?

    Very welcome! Mine idled like a kitten even with the long duration cams and 1000cc RC's :)
  2. I

    Simple question

    Cool always thought they made a 1 piece for our cars (saw one on a local car at a dyno day a few years back)
  3. I

    Been busy with this recently - Building the fastest FWD car... ever....

    Fastest ever??
  4. I

    1.5JZ + Standlone - Batch spark/fuel or Sequential?

    My Cam's were 280's ;) Batch fire on IGN isn't a big deal if you're using 6 coils/6 igniters, even on twin post coils it's marginal as the side firing the dead cylinder doesn't dwar very much current as there's no cylinder pressure. Sequential on Injection makes a HUGE difference if you're...
  5. I

    so i need some help with ride height settings

    If it's just rubbing at the lumpy bits of the Liner you can heat them up with a heatgun and push them in a bit, I ran 265/35/18's on the front fairly low and did this to good effect.
  6. I

    so i need some help with ride height settings

    Thought he said it was rubbing the Liners??
  7. I

    13.8 @ 100mph NA-T 88 Supra

    Probably the single stupidest a340e Mod known to man.....
  8. I

    so i need some help with ride height settings

    No one will be able to answer this as it's dependant on each car and the way it's been setup, ie: Tire size/wheel offset/suspension settings and so on. May as well ask "How long is a piece of string"
  9. I

    so i need some help with ride height settings

    This section is "Moderated" so each new thread needs to be approved by a Mod before it can be "seen", posting the same thing again will just result in more work for the staff cleaning up the mess.
  10. I

    Simple question

    Don't see a reason for a correction as we're discussing which QR Hub will work on a mk3 I figured "hub" was redundant....
  11. I

    What did you do to your supra today? Pics

    I remembered mine ;)
  12. I

    Simple question

    You would need a QR specific to the Toyota splines/shaft diameter.
  13. I

    lower suspension arm

    Can you get a jack under it to preload it a bit?
  14. I

    Project Clean 87

    Nope I'm talking about a Cheesegrater file, commonly used for Bondo and works exactly like a cheesegrater ;) Personally wouldn't use it for anything other than emergency repairs and never on a thread, that's what Keenserts/Helicoils are for.
  15. I

    Project Clean 87

    Dunno, never used it but I did inherit an engine that had that repair done with DevconA Ti epoxy...... They just splooged it on the snout installed the damper and bolted it down... Trouble came trying to pull the Damper, totally trashed the engine getting it apart and destroyed 2 pullers...
  16. I

    Project Clean 87

    Yep, very little to do with "Balance" on our engines as they're internally balanced ;) The PMoI is so low that close into the centerline of the crank I doubt you could measure a difference in balance even without the JB Weld in place.
  17. I

    upgrading injectors

    Very welcome Grubbs, happy that someone listens to the dodery old fool ;)
  18. I

    Building Bottom end. Have questions

    You need to wait till it's all apart and inspected/measured before buying parts Fubar, pay close attention to the Deck area around the Steam holes on the exhaust side it's a common place for 7M's to crack making the block useless for a performance build.
  19. I

    upgrading injectors

    The ECU "might" have enough range in closed loop to pull some fuel so it will idle/cruise if the Injectors aren't too much bigger BUT it will be pig rich everywhere else and will drop power...
  20. I

    upgrading injectors

    ummm you don't pull the top off anything to fit injectors..... If you fit bigger injectors without changing AIRFLOW or any way to retune the engine it's going to be rich.
Top Bottom