Search results

Car looks awesome man, hit me up if you need a hand as well, Id love to see the car in person. Who new there was MKIII population in the pullman/moscow area

I picked this up at the wrecking yard the other day, its almost idendical to a B&M stacked plate cooler and measures 11X11 which should barely fit with my new intercooler location. This is the only concern I have with it. The ports are quite a bit smaller than the 1/2 inch lines I will...

Some un expected parts showed up at my door today I only ordered them 3 days ago, and they already got here I picked up a few oil coolers at the wrecking yard today. The large one is Idendical to a B&M stacked plate cooler and measures 11X11 which should barely fit with my new intercooler...

its a spearco core with no name endtanks on it

If the car is stock 5 psi is pretty normal. If I remeber correct 5.5-7.5 psi if its a manual, 4.8-6 psi if its an auto is factory according to the tsrm. Even if its a manual, with milage+ restrictive stock exhaust+ stock gauge inaccuracy, 5 isnt bad. That sound like something is spinning really...

A few things came today Some more goodies for delilah

Lotek does http://www.gaugepods.com/

Finally have a little room to breath, the worst part is you would never guess how many hours of clean up went in to this. Still Looks like a mess My downpipe fits about as close as you could ever hope for so I was pretty satified there. Tucks up tighter than my bros RT Also got a good...

debree in the cylenders right?

Right now Im looking at options assuming my block isnt warped. Its got 24k on a NEW toyota block and has never overheated from what I know. Im trying to avoid tearing the bottom end down. I wanted to know what my options were to smooth it out while still assembled. Its not a problem getting to...

diamond paste with a regular lapping block?

Can anybody confirm if they actually dont work with an oem clutch, or if its a single incident, I got a killer deal on a fidanza flywheel, but am keeping my stock clutch:(

What about this kit? http://cgi.ebay.com/ebaymotors/REMOTE-Oil-Filter-Mount-Oil-Filter-RELOCATION-KIT_W0QQcmdZViewItemQQcategoryZ46095QQihZ011QQitemZ320165968437QQrdZ1QQsspagenameZWDVW If I went with this wouldnt it eliminate the need for a GE oil stud since the adapter has male threads?

I have my set up figured out for the most part minus what filter mount to use. Iv got my lines and gasket kit all squared away I just need a GE filter stud! Does anyone know where I can get one? cant find a source anywhere.

So this is what Im thinking for my oil relocation kit http://store.summitracing.com/partdetail.asp?autofilter=1&part=EAR%2D1178ERL&N=700+4294818392+115&autoview=sku With thermostat, http://store.summitracing.com/partdetail.asp?autofilter=1&part=PRM%2D1070&N=700+4294843279+115&autoview=sku Along...

How many psi would shimming 2 or 2mm give me? 100 psi off Idle is a little exsessive for my application. Also, Who has run a light weigh flywheel? I have a chance to pic up a fidanza really cheap but am not sure if its something I really want? What does this do to everyday drivability? How...

Who caries MDS, got a link? Some of the kits on ebay looked better than others and did come with viton valve seals. I took my first good look at my oil cooler today, man is the stock one small. Will an 8.5X11 actually fit next to the intercooler? The other issue is Im going to be putting a...

So Im getting ready to do a HG job on my car. I'm pulling the block and getting everything machined for a MHG. The lower only has 24K on it so I should be fine there but I did want to pull my oil pump and check/ replace it along with shimming. I have a few things I need oppinions on. 1...

Ill probably pull the trans with it, it sounds just as easy and then I can give it a look over too. So any oppinions on what gaskets to use??? Also Is it worth it to swap out the oil cooler? I'v heard of a few people who have gone to aftermarket ones or put an RX7 oil cooler on?

The up side is we have just about every tool you could ever need, or never need as well for that matter:icon_bigg