Search results

removed

this was taken a few weeks back, at a local meet. love the way it came out.

a few days ago i decided to do some wiring (relocate heater control) when i finished i hooked the battery back up, started the car and it ran like Sh!t.. stumbles/hesitates/doesnt want to start when cold, AFR always super lean, i have to put my mainscale at +5 just for it to run, still...

my best launch to date so far 1.80s 60ft. my coupler coming off the turbo decided to explode just as i was about to shift to 4th gear,:icon_evil NA power the rest of the way:biglaugh: http://youtube.com/watch?v=U6VjKPnVeJc

quick race vs. a turboed integra enjoy:icon_bigg http://www.youtube.com/watch?v=3qkJFrfh-YA (i didnt see the vid section at the top) sorry...

went to the 1/4mile drags on friday, this is the best out of 9 runs reaction------+0.96 60ft------2.41 330ft-----6.29 ET@594ft------8.72 1/8mile et------9.24 1/8mile mph-----86.37 1/4mile et-------13.76 1/4mile mph-----109.24 18" wheels with 275 35 falken azenis @35 psi. lol i'm...

i picked these wheels off CTsupra a few months back and just got all the rubber mounted. 18x8.5 +30 and 18x9.5 +35 Falken Azenis rt615's 245f and 275r. thanks CTsupra i love the look:icon_bigg not sure why this pic came out the way it did. but i like it what do you guys think? pos or neg...

i just got a full set of Falken azenis RT615's 275 rears and 245 fronts with winter dragging on and on here :( i havent had a chance to try them out yet. just curious to see what people think of them.

i figured i'd show what i've been up to with project MK3. the harness was something that was bothering me for sometime, so i decided to re-rout it. dealing with 20+ year old wires and plugs required ALOT of patience. this is just after starting the teardown. and here's what it looks...

OK, this probably wasn't the greatest idea ever, but man was it fun:evil2: even the police that showed up afterwards were amused:biglaugh: i wanted to blow the tires, and another 20 seconds and it would have happened, however my lower rad hose had other plans:nono: i know most will...

a short vid of a buddys 66 454 BB chevelle wrecking some tread. :love: the supra makes an appearance too:evil2: enjoy http://www.youtube.com/watch?v=g-9yrCQmCbs and this one finally wrecked my rear pads lol http://www.youtube.com/watch?v=i_-9h9WezXU

not the greatest quality (cell phone). just had to light up the slicks:evil2: http://www.youtube.com/watch?v=E8fYHCyt_wM

well i dont know what else to do to her, and winters coming so i think i'lll take a break from the PIT. here's an engine pic and some dyno #'s BTW the dyno was at 17psi on 94 octane

full turbo back in 3", no crush bends either. the downpipe has a 1 foot flex section in it just incase i scrape. all new tabs welded on the chassis and bolted up and finished with VHT 1500 degree flat black. ripping the old stuff out. cut-out+cat complete what do you guys think?

so i needed a new valey cover, called toyota:nono: no thanks. called up a guy i know and had 10 pcs. laser cut for me out of mild steel. and then applied a layer of carbon on top using high heat resin and clearcoat. long story short, i have 8 of these left in Carbon fibre you can see in...

i haven't been able to find the answer to this so here goes. i got a ssac manifold but the studs on the bottom wouldnt go through the mani. i drilled it out and it's fine, but what do you do about the exh. gasket? it seems like i have to remove the copper washers on the gasket that seals...

well i got my head back from my builder, i asked him to helicoil the studs and put 7/16 studs. i tried to put my manifold on last night and three studs are in crooked. the manifold wont fit at all:3d_frown: how can i remedy this. i'm calling this guy and freaking out tomorrow, just want to...

some will like it, some will hate it.. lets hear it my egine bay is now covered in carbon:biglaugh: heres a few shots of the rad support completely done, the rest still needs the final clear coats. what do you guys think? any imput is welcome:icon_bigg heres a good look at pretty...

the machine shop took 10 thou off the bllock and head combined and i had taken 6 thou off the head two years ago.also it was not bored out just honed. what thickness hg do i need? i think 1.4 will be good :icon_conf <<<<???? i had it lapped to an RA30 smoothness paypal in hand and i...

just a few shots to show how my interior is coming along:icon_bigg i cant wait till it's all together.. i dyed the carpet, ran all the wires along factory wiring harnesses and ran the batt. cable iunder the carpet. i might just wait until i get the maft-pro to install the dash, i figure it...