Search results

hey everybody, dont know if we have any lawyers or legal professionals here, but i figured id ask. I need to have an attorney (i think) submit a letter of cease and desist to a website owner and web host. i programmed a php back end for a website for a company. they originally offered me a...

ok, so yesterday, this old guy comes in to my work and puts his keys on the counter and told me that he didnt want his truck anymore. he signed me off the registration (canadian form of transfer of ownership) and called a cab to get on a bus. i have the truck now, its an 83 dodge ram w/ 318...

ive got my innovate lc-1 hooked up to send as emulated signal to the stock ecu to keep it happy. its working fine. the only thing i havent done is get rid of the check engine lite (code 21) for no sensed resistance on the heater wires. tsrm says spec is 3.0 to 3.6 ohms. if i take a 1/2 watt 3.3...

ive got a code 21 and 22. 22 is from the connector breaking off, code 21 is because my stock o2 has been removed, emulated thru my wideband, and the heater circuit is open (no resistance). the car feels like its pulling timing (rather sluggish) is there anything besides the knock sensor...

i wanted to post this thread for a few reasons. I have an upper end knock, caused by too much wear in the cams, even though my lifter shims are very close to being within specs, it still knocks a lot. i grabbed a set of good cams from the junkyard (n/a motor) and here is what they looked...

I made this sheet today cause I was bored... All you do is first measure the clearances (measuring order provided), and then pop out the shims and measure them. This worksheet will automatically calculate the replacement shims needed to bring the clearance within spec and even give you the...

hope this aint a repost... but pretty funny http://youtube.com/watch?v=hMnk7lh9M3o

So, im driving out of the parking lot at my work today, and i heard a hissing sound, and then a wierd squirting sound. i didnt make the connection at first, but it occurred to me to look at my oil pressure gauge, and sure enough it was at zero. i whipped my hand up to shut the car off, and...

im sure that ive seen it before. i think either becauseican or nashman originally posted it. it was a way to cut and re-weld the pre-89 motor mounts to fit the post-89 subframe. anybody else remember?

this question is for anyone who knows off-hand or has an r154 apart and wouldnt mind looking for me: how many teeth are on the rear wheel speed sensor gear in the r154 tranny?

well, ive just installed a new speedometer cable from toyota, and it lags. when i start off from a dead stop, it stays at 0mph, until i hit about 25 or so, then pegs up to whatever speed im at. if i am driving, and almost stop, but keep rolling, it works fine. no lag. could it be a problem...

so, i had been messing around with my safc now that i got my wideband. a situation that i encountered was that if i got a good tune down for wot, as long as i had part throttle changes it would start making the afr's jump all over the place when i did wot runs. i have since then disabled all...

this is pretty funny http://www.youtube.com/watch?v=TijvTiLi-qk i lol'd cuz i used to be a restaraunt manager for mickey-d's for 4 yrs.

been driving with rodknock for a while now... and within 1 month im gonna pull the engine and rebuild the bottom end. i cant find anywhere in the tsrm that says to check the connecting rod big end for roundness, but i remember seeing it somewhere. anyone? what im planning on doing is...

anybody else a korn fan? seen this? http://www.youtube.com/watch?v=3cXCJO9vBOw comment plz. personally i cant wait till feb 20th to see the rest.

ok electronics gurus out there, heres my dillemma ive added a shock sensor to my car in the spare tire well. it is the type that completes a ground connection whenever motion or shock is detected. keep in mind that it is usually for less than half a second that the sensor completes the ground...

Well, it's been a long journey, and I've learned so much. Started off with my POS that i got for $800. 89 Turbo, 5spd, Targa. I had been looking for one of these for a while now, and when i heard the price, i jumped on it. Wasnt a great idea, but i love putting time into it. When I got the...

anybody ever replaced valve stem seals without removing the head? how? or is it not reccomended?

Well guys, here is what I found out: My cable was broken a long time ago. Im talking about the long, 2-piece cable for turbo 5 speed Supras. I decided to start ordering the parts to fix it when I came upon a discovery. I ordered a cable ($7.91 p/n ATP-Y-844) from RockAuto.com, thinking it was...

well, im halfway thru the removal of my head, and when i took off the pcv hose to the block, i can see a lot of milkshake buildup in there. i know that there was a serious leak and it was driven for a little while even when overheated. i didnt have another choice at the time. i already have a...