Search results

So, years ago I threw out my stock Supra seats because they were all chewed up. Long story short, I bought a Corbeau GTSII seat from a friend over the spring. Not paying attention to the seat orientation, I bought a damn passenger seat. I am not interested in racing harnesses and want to use the...

When I turn the key to acc, I do not get any power to the old relay wires that are spliced together (see pic for ref). Am I correct in that there should be power running to these when key is turned to acc? I also tried it in the start possition with no luck. I'm going to try and replace all...

Looks like the small bottom port goes to the VSV, the other one next to it goes to the tank (i think). Anyone know where the top port goes? Intake tube? hmmmm... Excuse the crude MS pain pic and the long vacuum lines, which will be trimmed to fit when I figure out where to mount it...

Can anyone identify where this vacuum port goes? Thank you...

Looking at the coolant flow diagram, it appears as though one of the nipples :naughty: on the water neck is the feed and the rear silver pipe (smaller one with hose attached) is the return? Can anyone confirm this please? And the nipple on the 2jz water pump is a weeping port that just needs a...

Would anyone know, or be able to snap a pic of how these wires go into the clip based on the clips position? This harness had a more square connector and my spare harness had round one (shown here). My friends car also has the squarish connector, so not sure how this one should go. Also, would...

Anyone know what bolts I need for the brackets? Anyone know if the 2jz bolts would be the same? I could try ordering from Toyota if the 2jz bolts would be the same. Thanks, Ryan

I have an e-mail out to Driftmotion, but I heard they were busy, so I probably won't get a response back for awhile. Figured I would throw it out to the community in case someone else has this problem. I bought the DM SS braided line for feed, which works well, but I want to run stainless for...

I just finished converting my fuse box over from MA70 to JZA70. I should have taken better pics when I tore everything apart. Can anyone tell me where these go? This is a ground that goes somewhere. Not sure if it went to the engine, or there was a spot for it in the engine bay: And...

I bought the PS reservoir that beech perf makes because I didn't have one with my shell and swap. Just wondering how and where people installed it. I can't seem to think of any good ideas at the moment. Thanks!

Mine has a hole in the side. Thanks in advance!

So, I am getting around to putting the motor back together. Put in ARP bolts and studs, new head gasket, the 2jz cams I bought from someone on here that they were running in their 1jz, and cam seals. Here is my dilemma. I'm not sure if anyone else has this issue, or maybe this is acceptable...

I have this bracket, which I believe is for where some alternator wires connect to. I just can't figure out where the heck it goes in the car. Can anyone shed some light? Thanks in advance...

Does anyone know what aftermarket radiators will work with the hydro fan? I am not really interested in spending $400 on a Koyo. Anything cheaper then Koyo that will work? Thanks in advance!

Hey everyone. Been having a heck of a time deciding on what clutch to go with. I'm hoping that some input from the community will help me reach a decision. I have a 1JZ w/ R154. I have laying around an all aluminum one piece flywheel, ARP flywheel bolts, and flywheel bolt locking ring. I was...

Any idea if the crank pulley is suppose to stop at this point? It doesn't seem to want to go any futher. All of the other pulleys work great, though...

Here is my stupid post for the week... I took out the clutch and flywheel from my 1J and found an OS Giken clutch and flywheel. I want to sell this stuff because I bought a new light flywheel and looking I have my eye on a stage 3 clutch on driftmotion's site. Could anyone give me specifics...

:aigo: I can't get it off. 1/2" breaker bar, socket, extension, 2 foot pipe, and a support under neath the rachet head so it doesn't move. Have to borrow a compressor + impact gun now. Am I missing something here? Are they reversed threads?

So I decided to take a break from siding the house and start working on the 1J this afternoon since its really hot and my allergies are effing killing me. I pulled the valve covers, which seem to be leaking some oil, and I also pulled the plugs to check out their condition: Pretty...

Hey everyone. I am almost done figuring out the wiring on the cut harness I received. Could anyone tell me what the following wires go to? Much appreciated! According to the diagrams, this is the dash ground and ecu ground on the M1 connector: These three brown wires match the M1 dash ground...