Search results

Anyone here had problems with the belt shredding with relocating the alternator to the air con pumps place. I am waiting on another set of spacers as they are slightly different in width but not sure this could cause the problem

Please can someone confirm the thread on the 3 spare holes on the pulley I dont think they are M8. I need to make a puller to get it off as mine is well stuck on with a new key

Anyone know what type of thread the cold start injector banjo bolt is. Ive done a search but just found the fuel rail end is M12 but the inector bolt is much smaller and I dont think its metric

Fitted my C's short shifter today but it will not go into 5th. Finds every gear even reverse but will not go inot the top corner. Standard one works fine Any ideas?

I'm in the process of putting in my accumsump but have a few questions. What preasure do you use on the air side. My oil pump will be a brand new 5mm shimmed one. I have mounted it on the back of the rear seats as my boot is full of an ice install. Do you think it would be ok to mount...

Just taken off the head off due to a snapped water union at the back of the head. To my suprise is had/has a MHG but just one problem below The scratches must have been there when the MHG was put on as a can see the marks of them on the gasket the engine ran fine so it must have sealed...

Ok so Starting my new oil sytem and I'm using canton take off adaptor and and an adaptor for the acusump the trouble is the threads want meet I know they are the right ones off the car but on the car the oil filter stud isnt long enough need about 10mm more on the oil filter side. Can somone...

Might be in the wrong section but it is connected to my supra:cry:. Ages ago I ordered and payed through payapl for a load of earls bit from SCHORR PERFORMANCE 1371 ROUTE 25 MILLERSBURG, PA 17061 United States 717-692-4667 schorrperf@aol.com They nerver turned up he said he would give...

I'm trying to get hold of a home phone number for a certain person I have name and a zip code but is there anywhere that wont charge me? Or if someone has an accont with one of the seach companies and wouldnt mind doing one for me then I can PM you with the details. Its a bad seller if it...

SOme of you may know from the help section that I was sent the worng set of AEM cam gears for my 7MGTE. Any way finall got the right ones but I would like to know what var the originall ones were for so I can flog them. They were slightly smaller than the 7MGTE ones but fitted on the cam...

Having trouble changing my timing belt. I'm using a Gates Racing one and have read the TRSM bit but I always come out with too much slack around the tensioner with the tensioner released AEM and Suprasport.com have sent me the wrong cam gears:1zhelp: :1zhelp: :1zhelp: :1zhelp: :1zhelp: :1zhelp:

What mantain the fuel tanks pressure and should it be maintaining that pressure even when the car is not on. I'm halfway through changing to a AFPR but if i scew the fuel cap down petrol starts pissing out so I have to leave the cap undone a bit. The car hasnt run in months though. Thanks

Where the crank dmaper pulley slides on. Probably a really simple newbie question but whats it for?

after taking my subframe off and now starting to put it back together I got to the steering shaft. I thought if I had the wheels straight and the steering wheel straight that wouls be that. I was wrong as it gave me 1.5 turns to the left and 2 turns to the right how do I sort this?:1zhelp:

pulled my idle controll valve off to yesterday bit two of the pipes were blocked up with what seemed to be mud. Plus the ends of the pipes had started to rot away. The car idled fine before but what couls be the cause?

Is there any chance one of you kind folk would ring up AutoSport wiring for me. I bought a patch harness a few weeks back but recieved nothing and the tracking info say attempted delivery, which I have seen no sign of. I know I should ring myself but it would wipe out any saving I made buying...

Just had my HKS sports turbo re-cond and was planning on using a different pipe set up, but have hit a bolt clearance problem. That for the the oil drain pipe and the bolt in the way. I thought I could rplace it with a button head allen key bolt to give me that few extra mm of clearance...

Where can I buy one of those short ECU loom conectors to help avoid butchering the original loom when installing piggy back ECU's Assuming I get my maft pro:1zhelp:

Anyone got any pics on how they did this. I dont fancy sticking bolts through my brand new $400 rad. I have some ideas but thought you lot may have done it a better way

Tried fitting my HKS coilovers this evening but ran out of light and warmth. Anyway I only got japanese instructions with them so not sure if there is a left and right to each shock. If so which way should the little adjustment knob at the bottom of the shock be pointing( into the car or...