Search results

Not a bad price??? That is an incredible price where did you find them for that cheap? For example, Driftmotion charges $87 for the rear camber bolt set....

So the first thing I need to do is determine if they are seized or not. I guess I should buy new bolts even if they aren't seized? I was quoted 5 hours for front and five for the back, so $1000 job to install all bushings.

How much should I expect to pay for an Energy Suspension Bushing install (front&rear upper/lower control bushings)?

Ok Ace, everyone is paid up in full for the round 5 coilover buy. What kind of time frame are we looking at to see product at our doorsteps?

I'm pretty sure that throwing someone off would be nowhere near as tortuous as making them WALK off on their own, and that would be very un-pirate-like not to torture.

is that an LS3??!

I do. So following the 1JZ EFI diagram, http://www.1jz.com/tech/docs/wiring/WiringEFI.pdf (pg. 3) it shows a blue and red wire coming off of pin#7 on the 1J ECU, which then goes to pin #11 of the IH1 connector, which is then mapped to my MA71 B1 pin#11. It then shows the blue and red...

So plug "T", pin#7 then? ---------- Post added at 05:09 PM ---------- Previous post was at 05:01 PM ---------- Where is the blower motor resistor located? The TSRM gives inspection instruction for resistance, but it doesn't mention anything about location. I know it is a relatively flat...

Probably a month with actual shipping time and then customs. ---------- Post added at 10:41 AM ---------- Previous post was at 10:40 AM ---------- Great so everything sent off?

I don't know. What is the "a/c pin"? Looking at the A/C circuit diagram, I see an "A/C short pin", is that what you are referring to? I've got the magnetic clutch going to the clutch relay, and then that goes to my #9 pin on my EA2. It kicks on fine, and blows cold (I installed new parallel...

Nice! Wheel specs?? I've already put all of mine on the car, well I only did the Wilwood's in the front, just upgraded rears with new OEM + powerslots, but other wise....I should put a pic up huh? Oh and I haven't picked up any sway bars yet. What are strong points of Whitelines over S/T or...

When I activate my newly charged A/C the motor bogs down pretty hard core. Is the throttle positioning sensor responsible for idling-up the motor when the A/C is turned on?

Is there a way to bleed out air that may be trapped in the ABS module? I left my rear brake lines open for a couple of days because I didn't know any better. I have replaced all brakes completely (BBK up front) and bled each one till clear fluid ran out. But I have been told that bc I left...

Technically not yet, Yota said he'll be able to get his out by tomorrow, so that will be everyone.

If I was going to go back and do it over, I would have taken my time and extended my harness to run it through the US harness hole in the firewall. I drilled a hole through the firewall. Allthough much quicker, I now have a hole in my firewall right next to my legs, which is a risk in itself...

I'm guessing the only person that will be able to tell us that is Grimsta...

Awesome. So the list as of now: 1. Chris Timerding- MKIII X2 Shipped *deposit paid* 2. TheTransporter88- FC X2 shipped *deposit paid* - FINAL 70% PAID 3. Taka21- MKIII X1 (with 1UZ) shipped *deposit paid* - FINAL 70% PAID 4. Poboy69- MKIII X1 Shipped *deposit paid* - FINAL 70% PAID 5...

nothing like delayed gratification :-(

Mark Twain was the man

Saaaweeet! Keep it up man terrific stuff!