Search results

hrmmm... AWD v8 turbo supra? sounds like a plan.

are you going to get a roller or dynapac?... or both... :P

Here is a 2nd gear pull, 15psi and a little wheel spin round 5000rpm. http://www.youtube.com/watch?v=QQ3GUy7HZ_Q enjoy

removed the spare wheel, jack and some other heavy items in the boot, also keeping fuel level at 1/3 full, with the reduced weight the clutch holds most of the time. @ 15psi Since fixing boost issues the turbo comes onto boost quicker and therefore there is less torque shock also. I'm still...

ahh i get you now, can you remove the compressor housing of the ct26 when you get it off (just a circle clip) im intrested to know if yours looks the same as mine.. only suggestion i have is look to make sure the airfilter is %100 intact / and there are no contaminants on the inside of the...

i think you mis-understood me, your turbo is now unbalanced.. replace it before you drive the car again. go looking for shards of metal that may be lurking in your intercooler piping just waiting to wreck your motor / exhaust wheel... oil that pooled in the intercooler side tank caught mine and...

IJ, Excuse my ignorance, what is Turbo FOD? (my guess is turbo fodder?) looks exactly like what happened to my ct26, id go looking for missing fragments of compressor wheel. FYI - The noise is known as Death whine. Here is what happened to mine Crap photo but you can see many scratches here

nasty, looks like my old ct26, see other thread

Looks good! you don't need cams to get 400rwhp... installing cams will change the entire profile of the motor so if you do make sure you do your homework. Good luck with the build

nah the hose clamp dug in on a funny angle and sliced it, it wasn't a ebay one either :( all the little and time consuming things were done on the dyno such as idle tuning, correction maps etc, a airleak only affects on boost, the tuner i use has a factory in the middle of a industrial estate...

It wasn't a pure waste of dyno time, i did perform a leak down test before i installed the haltech(car didn't get driven for 3 months?) with a small tyre air compressor which didn't reveal anything, only at 30psi into the intake charge did i notice any kind of leak, before I fixed my leaks the...

no i didn't..its been on my "todo" list for a while along side replace cooler pipes, My car runs on a map sensor anyway so leaks don't affect AFR's in the same way it as AFM's

Cheers! yeah shadow grey in Australia is next to impossible to find, at first i didn't like blue all that much but i love it now especially with the two tone. found 2 major boost leaks! on the factory ecu i had issues boosting above 9psi on a stock ct26, and 4-5 psi on the T61, I got off my...

Success, think i found my spool issue! got my air compressor back from my parents place in the bush (lent it to them so they can pump up the tyres on the tractor etc) my air pressure regulator arrived in the mail today, i used PVC caps with a air compressor fitting tapped and threaded into one...

I've mangled big breaker bar against the ground with the starter method on my daily, make sure you pull the EFI fuse, last thing you want is the motor starting with the balancer loose.... on my supra i put the car in gear to lock the crankshaft and undid the bolt with a big breaker bar with a...

the shocks are good, i will admit they could be a bit harder under the "sport/normal driving" but i think it has a bit to do with springs, when they firm up the dampening rate is good, makes suprise speed humps alot easier to deal with and speed humps in general, i cant compare them against...

6000km, not sure in miles but i'm sure you can work it out. ---------- Post added at 01:38 PM ---------- Previous post was at 01:31 PM ---------- not sure, i used -4 feed line - teflon braided and -10 drain line - rubber braided Used a banjo setup on the block feed hole and the restrictor...

Cheers, it came out nice i think. it needs to be redone... Yeha i've still got the entire interior sitting in a storage shed, i used a vinal dye for most of the roof sections as i didnt get a targa top blue interior, i decided to get creative came out awesome! i'm a fan of dark roof lining, i...

cheers, still work in progress. It's all back in one piece now, planning to completely redo the intercooler piping, fit my FFIM and change gearboxes soon as i get my air compressor back im going to test for boost leaks in the current intercooler system, i'm betting ill find a big leak... I've...

The guys that manufacture this turbo are pretty keen on fixing any potential issues with the product which is a really good sign, I've supplied them with pictures and a description as to the issues i've encountered, with any luck they will use it to improve the product. The important thing to...