Search results

  1. B

    Where's my Compression??

    Leakdown test
  2. B

    So... Someone hit my car in the car park at work yesterday

    Sorry LilMiss People suck no matter where you live.
  3. B

    Hose question

    That might be the vacuum source for the vsv's under the intake.
  4. B

    Cylinder Max taper spec?

    Damm you guys, now you made me do research. Sorry for the confusion. 1987 Hard Copy TSRM page EM84 Procedure and Spec out of round and taper 0.02MM / 0.0008 Inch Online manual Page EM74 Procedure shown no spec.
  5. B

    Cylinder Max taper spec?

    Page: EM84
  6. B

    Take a look, what do you think?

    PO must have had a overcharge condition. Either the vehicles charging system or a battery charger.
  7. B

    Questions on the two vsv's under the intake

    As Radiod said, they mount to the lower intake bolts. In some situations, Possible hard start hot if removed.
  8. B

    Switch to Synthetic = numerous leaks

    The CPS has a external O ring located near the base on the housing assembly. These get hard and brittle. Internally there is a seal for the shaft assembly which also gets hard and brittle. This seal is replaceable but is not available from Toyota.They can be purchased aftermarket. Disasembly of...
  9. B

    Whats the trim size for a stock ct/26?

    Taken from John Lundfords site: Stock CT 26 inducer exducer 1.811 2.559 40 Trim 1.870 2.950 50 Trim 2.122 2.950 57 Trim 2.230 2.950 I have a 50 trim I never measured it, but it is larger than stock.
  10. B

    timing belt cleaning

    Repair all leaks, clean sprockets and surrounding area well, replace belt.
  11. B

    HKS TEMS underdash kicker panel plugin - Where?

    No tap in of wires needed at the module. Right passenger kick panel, plug and play. Power and ground connections done at the original TEMS buttons wire connector. All this of course if your harness was not hacked. If you have any other questions PM me. I had the system in my car at one point.
  12. B

    Injector cleaning services

    Cruisin performance: Excellent price and service.
  13. B

    Lower radiator hose replacement

    FWIW The lower hose from a 86 Toyota celica supra 2.8 5MGE works fine without the loopty-loop.
  14. B

    Injector #1 not firing??

    Check the ground side.
  15. B

    Cleaning cylinder walls before assembly

    Moreso, a de-glaze ball hone. And as IJ said hot soapy water and a scrub brush. This has been the standard and recommended way for years. Blow dry and get that block protected fast with your choice of lube/protectant.
  16. B

    Burning oil and smoking after fresh rebuild!

    Now the machinist I went to for my head in the first place, says he'll inspect the head for me. What's wrong with pulling the head...I don't see any harm in doing so? There is nothing wrong with pulling the head if you are confident thats where the trouble lies. Although once you remove it...
  17. B

    Burning oil and smoking after fresh rebuild!

    FWIW DO NOT pull this engine apart untill you know whats wrong, or the specific area to check. From reading your posts and reply's, do yourself a favor and let a professional look at it. ( No offence directed towards you or your friends. )
  18. B

    1/4 Mile Time's and Dyno's Stock/Moded

    I have three differant articles. 15.16 @90 0-60 6.7 15.0 @91 0-60 6.6 14.9 @94 0-60 6.4
  19. B

    single wiper blade?

    A kit is available Very inexpensive JC Witney
  20. B

    How do you keep your shop organized?

    All great idea's. Most that I follow. Throw/sell all junk. Alot of people don't need more room, if organized. Do you really want to waste time selling a used ball joint for 10 dollars? After the time it takes to post, Pm's back and forth, Packing, tape, a trip to the post office. You now made a...
Top Bottom