Search results

due to some issues we are having with a friends car. can you use a 89 ecu on say a 90, or 91, 92 etc.. engine harness? the harness he bought is supposed to be an 89 harness. but idk. we have tried 3 diff ecu's that are all supposed to be 89 ecu's,. and same problem. it breaks up really bad under...

i found some toyota waste spark coil on plug coils. would prolly work great with a 7mgte. idk if it would need the is300 wires or not. these were on 4 cylinders. they had 2 of them so i grabbed 3 coils. got the clips as well. anyone with the is300 coils that can lmk if the wires from those will...

http://www.diyautotune.com/catalog/ebc-electronic-boost-control-solenoid-kit-p-285.html?osCsid=6a728b845c79c4fa71d35067224b059e been looking around online and think im going to do this. thing is i was wondering if there is any way to adjust the boost flat across by kpa or do you have to just...

i asked this before and i swore i had responses but after searching most the day i cant find it. soooooooo, i was wondering what sort of timing maps people are running and if you can post them up that would be great. either by rpm/kpa or rpm/boost would be nice. im running into a couple hicups i...

this is my friends 75 toyota celica he bought prolly 5 weeks ago. it had cut springs front and back, cut way too much. and some 13in eagle wheels. we did coilovers up front with 350lb springs as i had them lieing around and stock front struts for now. and then got some springs from the rear of a...

well, got some really rare hard to find stuff, soooooooo, ill be running a 6m with ~10:1 compression, trimil header modified with 3in collector and 3in exhaust and 3 40mm dcoe weber carbs. heres some mock up pics on the engine. still need to clean everything up and media blast the parts and...

i got board so decided to try out the video feature of my digital camera. i dont think it came out too bad. didnt see a video sextion here so hope this is the right place for them. first vid is just the engine idling. 900rpm's, lil over 20in of vac and like 800deg egt. as you can hear it idles...

i have a tilton 7.25in tripple plate clutch. it is unsprung. i know i have seen sprung hub setups before for this style clutch. it has a sprung hub with 1 disc on it and the outer part of the hub is splined. then the other 2 discs the inner part is splined to fit the hub so it can be put...

i searched and found that tilton makes clutch discs for their 7.25in multiplate clutches with a 29mm 21 spline hub which is what fits the w58 and r154. also quartermaster will make the flywheel for the 7m for $270ish. used tilton tripple plate clutches got for less then $150 shipped on ebay and...

i am always seeing people say to reinforce them blah blah blah or they will crack. yet i have NEVER heard of one cracking or seen pics of one that has cracked on a 7m. all ive ever heard of is claims and pics from a honda version that was sold like 5+ years ago. so for this thread, all i want is...

heres the setup i plan to run. ms2 on v3 board with flyback for low imp injectors 4bar map on the board 780cc/min injectors low impedance gm air temp sensor gm engine temps sensor dual edis 6 with cop coils 7mgte tps for now, ford tps on ford 75mm tb later with ffi aem wideband o2 sensor...

this is a thread of somewhat commonly needed tips and tricks. i will add more to it as i think of them. again, just copied this fro mthe other forum i posted it on. figured it may help some folks. CRANK PULLEY BOLT REMOVAL! best way to remove or tighten that bolt(no nics on the inside of...

well, tilton no longer makes their flywheel for the 7.25in multiplate clutch. does anyone else know of a company that does? i was told before tilton would make that flywheel again it would need 10 orders minimum. this would be for the 7m of coarse.

ok, ive decided to start another poll based on concerns of the outer diameter of the trans adaptor. http://www.supramania.com/forums/showthread.php?t=60506 question is, would you rather have the outer diameter the round 19in diamter, or trimmed already for the same outer shape as my...

edit: how about not put gay ass things like that checkbox on the forum when your constantly bitching about people not seraching? this is the only forum ive ever seen something like this in place. william Edit: If you weren't such a dumbfuck williamb82, you might have actually READ what's on...

plate will be made of 3/8ths plate steel and bolt to the 5m, 6m,and 7m and will allow any chevy pattern v8 trans to bolt to the 7m. this will include th350, th400, powerglide, 700r4, t5, t56, muncie, saginaw, t10, 200r4, etc... it would be for the plate only. prolly run ~$350 or so including...

i took all the measurments today that i need to make my t56 adaptor. problem is i think the r154 ones are a lil off. what i need is for someone with a r154 off the car that has a 7m bh attached to measure the 4 holes ffor me so i can compare. center of the intput shaft tot he center of the bolt...

ok, ive got solid works 07 and will be drawing up my t56 adaptor plate soon. need to dig the r154 and t56 out of storage for a ton of needed measurements. anyway, the file type on the sw is a .sldp something(dont recall it off the top of my head and forgot to write it down last night). will this...

i remember reading a thread either here or supraforums where a guy got rid of the throttle linkage on top of the 7mgte and instead changed the wheel on the side of the throttle body and hooked the cable directly to the tb and made a bracket for the cable stop so it would work properly. i have...

well, laptop fell off the bed and the screen broke. sooo, i need help finding a replacement panel for it. emachines wants too much to fix it. its a emachines w340ua and also has n10 listed on it. if you know someone with this part, a place that has it, or other emachine/gateway models that have...