Search results

Hello everyone, well to start off sorry for the long post, but I have searched but come up with nothing use full. It is a fresh motor, and it is a newly upgraded 57 trim Ct-26. First question is that when the motor was started after it warmed up the oil pressure was at only about 5-6 psi, when I...

Hey every one, just wondering if any one has use the kit that driftmotion sells for the 7m, if so how did you like it and if you had any pics of it installed. Thanks to every one.

Hey everyone, so I just got my chip in for the VPC that I am using on the new build, i am using it with a S-AFC2, I leaned out the VPC to get the car to start, it is idling high (1600), but smooth. When I try to drive the car if I slowly give it throttle it start accelerating ok, but when I give...

Hey everyone, so I fould a thread to install the VPC, and on the thread it says that the grey wire that should be there, and of all teh four wires I dont have a grey one, I have a yellow wire. I was wondering if I should move the pin location on the harness so that it matches the grey wire...

Hey everyone, so I have run into yet another problem trying to get the car running. So last weekend I was working on the car I finally got it running, and I let it run so it warmed up to opperating temp. It was idling rough, and I went to try to drive it to break in the motor, and as soon as I...

Hey everyone, I have searched and found nothing, I am trying to finish up the 7m build, and I was trying to crank it over to get oil pressure before start up, and I noticed I am getting no fuel pressure at all. its a new walbro, and when I run it straight from the junction box in the engine bay...

Hows it going everyone, I just had a quick question, because I am installing my AEM wideband. I didnt recieve the install sheet from the wideband, and I dont know where the blue and white wires go, red and black are obvious, but I am lost with the other two. Any help is appreciated. Thanks Ricardo

Well I am attemping to finish my rebuild, just today I swapped the grey and white clips under the dash by the ECU, and I have ABSOLUTLY no power anywhere. The battery is charged and as far as I know grounds are good. The car is an 89, and I put the JDM 7m in it that I was using before the build...

Whats up guys, I am trying to put the 7M in the car, I am using the soild motor mounts that I bought, and the engine doesnt want to seat all the way, am I doing something wrong, or missing something, it still needs to drop like an inch or so, its lined up in the brackets, the motor is just to...

Hey guys, I just my gauges in, and I went to install the oil pressure sending unit into the stock location, and it seems to be a different thread size, I tried searching, and I came up with nothing. If it is another size, how have you guys installed yours? Thanks for all the help, and hopefully...

Hey guys, I am putting my engine together now as we speak, and it seems like I have run into a bit of a problem, I have searched and found nothing, as I am torquing the studs onto the block not all of the studs are in equal amounts to one another, I was going to torque them to 80lbs per everyone...

I was wondering if there is anything that i could use that wont harm the CPS because i hadnt noticed that the dust cover had broken off and it was very dirty, will it be fine the way it is? or can i clean it with something?

:icon_mad: So today fucking sucked, I was driving home from the store, and I was on a small industrial road, it was pouring out hardcore, couldnt see anything, and the road had about 2 inches of water on it, because of how hard it was raining, I moved out of the way for another car going the...

Hey whats up guys, I was looking through an article and i found this add about CRC AFM cleaner, and I was just wondering if it would be safe to use, and have any of you tried it? If so where did you get it, and how much was it? thanks Ricardo Link...

:1zhelp: Ok guys, I am sorry that I am asking this, but I have searched and searched, but I can't find my damn answer. I just made a tester, and when I put it in the car, I hear all the air, and it seems like it is going straight through the head, what things do I also need to cap off, or do...

Well i just rewired my PCB board on my tach, so it would work after the na/turbo conversion, and after i finished the (air bag) light turns on, and it stays on, and i couldnt drive the car much, but it doesnt seem like the tach is accurate at all when i am at higher RPM's, so what do you guys...

:cry: Ok so I am driving down the road one day, and out of no where I start hearing this hummm from the back of my car, and as I gave it more gas it gets louder, and it doent really make noise when I am coasting. So when I got home I thought one of my rear calipers siezed, but it was ok, then I...

Hey whats up guys? Well as the tite says, my cars burns oil, and it smokes quiet a bit, I just recently did a compression test, and all my numbers were very high, and i think that it might be my turbo seals. I was just wondering if there are any other reasons why the car might smoke, before I am...

Hey what is up guys? Well this weekend I had time to do a compression test, and to tell you the truth I was extremly impressed with my results, I got around 175psi, plus or minus 1 or 2 psi, on all of my cylinders. So I just thought I would share what I think is good news to you guys, or what do...

ok so recently i have started to see a lot od smoke comming out the supra, most likely it is my turbo seals, but i am going to do a compression test later, i have a friend that told me to check my pcv system, because he said that he had a pcv system valve go bad, and his car started to smoke a...