Search results

There is a link to a thread in the 2jzge-T sticky, However the thread is for a 2jzgte engine. It states the camry throttle cable fits, but I think that is for the gte throttle setup. I need to know what throttle cable will work for the 2jzge in our mk3's. I'm sure there are plenty of people...

I know there are some differences between these transmissions. I'm in the process of doing a NA-T setup and am looking at mating up my 7mgte A340E to the 2jzge flexplate/engine. I have a 2jzge A340 bellhousing, but I am wondering if the pump/splines and everything are going to be the same...

My auto recently started having pump issues and started to slip. I am looking to replace the transmission with another used trans. (straight swap) I was wondering which year/model trans would be best to go with. I had shimmed accumulators on my old one and will probably do the same to the...

I am having some issues with my timing on my aem ems. Ive noticed that my timing map looks more advanced than others and I am trying to understand why. I double checked today and pulled my plugs to make sure I am not detonating. Everything looks ok. The major problem is that I will sync...

I have recently went standalone with a AEM EMS. I also did the dh61 ignitor/is300 coil modification and gm map/iat sensors. I used a startup calibration that was not boost comp yet and it seemed to start and run alright but real rich. I just recently took it to a local tuner and we had it on...

My car has been having missfire and cutting out/stalling issues. Wasnt getting correct spark out of 2 coils, although the coils were ok themselves. I eventually limited it down to the ecu (Pretty sure, I checked just about everything first) Anyway I got another ecu and put it in and no check...

Anyone have the measurements ont heir .020 oversized Probes? I recently had my block bored for .020 oversized NPR's and now I am going to go ahead and get Probes, but before I do, I wanted to make sure they are big enough. My bores were all pretty close but the smallest was 3.2901 and I'd like...

I converted my vpc/fcon setup to 550's. (was running stock injectors before without problems) I am running rx7 high impedence injectors and have deleted my factory resistor properly. I have replaced the fuel pump with a walbro unit and also put in a aeromotive FPR set at 30psi with vac at...

I recently drained my transmission and changed out the filter and shimmed the accumulators. Also the engine has been out and all the cooler lines have been drained aswell as the aftermarket cooler I have for the trans. I was wondering what amount of fluid do I need to buy and what process...

Anyone have a the cylinder maximum taper spec for our engines? I cant seem to find it in the tsrm.

Have all my measurements on my block, and was looking to replace all my pistons. I was wondering what I can expect as far as measurements on the standard sized NPR pistons. If anyone has measured their own or has the factory measurements or something I'd appreciate it. Thanks -Stu

Im planning on ordering toyota select fit bearings, and I understand how to get to the correct size and everything. I was just wondering if anyone has any insight on how you measure the main bore diameters? Do you take multiple measurements to see if they are out of round? Do you take a...

I have a VPC and F-CON already in my car, but I wanted to upgrade to 550 injectors. I noticed there was 2 seperate chips for the F-con for 550 injectors, and there was also one chip for just the vpc and 550 injectors. Im wondering which 1 chip do I need or do I need 2 chips. One for the vpc...

First off, I want to say that my car may have a upgraded fuel pump that I dont know about, Hopefully I will pull the tank soon to see. The reason I beleive I may have a aftermarket fuel pump is because the car had the J tube drilled out before I bought it. The car doesnt have an aftermarket...

I had a couple people comment about my wood grain on my mirror/lock switch covers. I dont really like them, but people noticed that they were different. I was just wondering if anyone knows if they were a factory option, maybe a dealer option or perhaps just some kind of aftermarket covers...

I have a small vacuum leak inside the cruise control pump or whatever it is called, Its on the Vac Side, and I made sure it wasnt the hose itself. I was wondering if it would cause any problems to disconect this port and cap off the line. I never use the cruise control and the pump itself...

Hey everyone just decided to make a build thread about my car. Its a 1988 Auto Turbo Hard Top. I found this car on craigslist around November of 2008. The owner did not know much about the car except that it had some performance "goodies" and he named most of them off, but he didnt know what...

Ive had my car for like 8 months now, and have always wondered if the exhaust is factory or not. I know it has a 3 inch downpipe without a cat because I put that in. The catback is what im curious about. It has 3 mufflers/resignators, and when I was installing the downpipe the first...

Has anyone done this on our cars? Can I do this in the car? My clutch is barely staying engaged and is starting to make a littlbe bit of noise. I would rather just replace the clutch, If I can do that on the car without removing the whole compressor. I looked on tsrm and it shows them using...

I looked on the mk3 EPC but I just cant pinpoint the part number for it. This is for a 88 turbo. I need the thick hose that goes from the Power steering pump reservoir to the pump. Mine is very hard and starting to crack. If someone finds it on the EPC could you link me to the diagram you got...