Search results

  1. I

    Revs

    Mik: Ummmm no ;)! Still waiting to hear what the Threadstarter considers high revs?
  2. I

    MK3Brent's T-66 Supra boosting vids. (2 links, one isn't ready.)

    Brent: Daytime vid please ;)
  3. I

    WTF is wrong with my shitt!!! HELP

    The valley could be full to the top of the cam boxes and it wouldn't get into the cylinders...... If the plugs were loose enough to allow this you'd hear it while it was running as it would "whistle". Have you changed anything in your setup recently? If not it might just be a bit of...
  4. I

    70 amp Alternator

    Have a look at the wire that goes to the Starter. Just trying to remember where I've seen FL's as none of my wiring is stock.
  5. I

    Cat. 5 super cyclone hit Australia

    Thanks Drew! It's been downgraded to a Cat 1 overnight so the worst is over!
  6. I

    finally got a tig

    William: Mines a 9000 xf or something can't remember the exact model but it's one down from the respirator equipped one and I LOVE it! It's a case of how much welding you're going to be doing V's how much you value your eyes! The lower level SG's would be fine and functional but it's a one...
  7. I

    Cat. 5 super cyclone hit Australia

    Dirgle: Thanks for looking out for us! It's a HUGE country so I'm safe down here ;)!
  8. I

    Revs

    Define "High Revving" ?
  9. I

    WTF is wrong with my shitt!!! HELP

    Describe the routing to the Catch Can please. Does it have a little K&N Filter? Is it recirculated to the Intake?
  10. I

    Oil leak

    The Exhaust heat pretty well cooks any and all rubber parts on that side of the motor. Even when mine was NA the O-Ring on the Distributor was dead and had to be broken into pieces to remove.
  11. I

    70 amp Alternator

    Yep it's NOT good! (I have that excuse for a manual)
  12. I

    70 amp Alternator

    AM: It's usually in the 5mm thick wire that screws to the terminal on the Alt.
  13. I

    pilot and throw out bearing

    This is why I recommended a Bearing Supplier as they will stock brand name bearings.
  14. I

    While valve covers are off, should I retorque my ARPs?

    Straight from Cometic's info Pdf! "Head Gasket Torque Procedure If you are using studs or head bolts, torque hardware to the manufacturers specification. Fasteners works like a springs and must have proper Torque or Stretch applied to carry the correct amount of clamp force. Also use the...
  15. I

    Cat. 5 super cyclone hit Australia

    LMAO Joe! :)
  16. I

    While valve covers are off, should I retorque my ARPs?

    Top Left of the triangle cutout looks like a crack?
  17. I

    Cat. 5 super cyclone hit Australia

    Other end of the Country from where Allan and I are and Mik/Miggles is over the other side so he's safe!
  18. I

    Forged vs Cast pistons...

    How do you know there's no difference if you haven't ran the motor with tight clearances? Again I'm NOT trying to be a Cock it's just that to make a statement like that you'd have to have solid comparative data to back it up... (I happen to agree that High Out put motors should have slightly...
  19. I

    I'm sick of stupid worm clamps.

    See if you can find a bit Hydraulic Hose Supplier/repairer in your area they stock them and usually not that expensive as they don't have the Ricer Markup that almost all AutoParts stores charge these days!
  20. I

    Getting sued for $125,000

    LMAO but you're "special" ;) Semi Auto is banned here after some fruitcake went nuts with a mini14 :(
Top Bottom