Search results

  1. I

    summit racing vagueness

    3bond 1207 is the best RTV I've used for pans so far.
  2. I

    stacked headgaskets

    LOL probably find 2 would seal quite well as there's so much gasket material it can flex to fill any gaps ;) (that and not enough compression to ever detonate) It has to do ugly things to the squish and efficiency of the motor at cruise though.
  3. I

    Cake II - The Sequel

    Headbolts are cheaper to buy ARP's Kai. (sorry forgot to tell you DOH)
  4. I

    stacked headgaskets

    Way back we used to use decomp plates with 2 gaskets..... A 7M is the last motor I'd try it on though ;)
  5. I

    Cake II - The Sequel

    They left 15 minutes after they arrived at my dealer ;) (same time as you sent the PP)
  6. I

    Speed Sensor Gear Q.

    Once you slip the 33485 tab in place it sets the depth :)
  7. I

    Cake II - The Sequel

    Kai: Looks good ;) HB Dude
  8. I

    Engine Dust Cover

    Buy some stainless bolts as well so if you need to remove it to work on the car they don't snap off ;)
  9. I

    Machine shop did more work than I asked them to do, now what?

    The shop "should" suck it up it's only labour.....
  10. I

    Speed Sensor Gear Q.

    33485
  11. I

    Speed Sensor Gear Q.

    If you pull the fitting out a bit you'll see a notch cut into the side of it. The Tab I'm talking about is a piece of flat metal say 10mm wide x 15mm long with an 8mm hole in one end.
  12. I

    Speed Sensor Gear Q.

    There's a notch in the side of the sensor that the little tab fits into to hold it in place.
  13. I

    Going NA-T give opinions?

    Viper: Dunno just seemed an odd place to put em ;) (It can't help but I'm not sure how much it will affect the stock coils as they're designed to sit up there anyway, Iv'e seen a few guys run em up on the firewall above the cam covers)
  14. I

    Ways to cure 7M oiling issues

    Dude if I had a problem with you you'd know about it..... You're overthinking things here to a power of 10. I'm NOT going to analyse every single post I read here I'm sorry I'm not a young man I don't have that many years left. Your idea was a complete failure and my elaboration...
  15. I

    Dual Walbros?

    Never seen the Hanger you're talking about most people just use a hose clamp around the stock hanger so both pumps are touching so need an isolator.
  16. I

    Bigaaron's "5M crank in a 7M" build thread!

    Aaron: Correct the stock hardening is Induction but it's quite expensive to set up for so most shops don't have the facility to do it. You can usually get away with a 10 thou cut on 7M cranks so this leads me to believe Toyota didn't use a lot of power during the process and the hardening...
  17. I

    Going NA-T give opinions?

    Viper: Any reason the coils are on the hot side?
  18. I

    What is JDM? I was told my car isn't.

    If your car wasn't bought and registered in Japan it's NOT JDM...... Here we look down on JDM cars as they're usually bought in cheap then have to be modded to receive Australian compliance and still sell for less than an Aussie delivered version of the same car. Also don't believe all...
  19. I

    Starter Relay

    20' of 15+ year old wire doesn't help. I run a 30a relay right at the starter so the only load the stock wiring/relay see is the coil in it and it 100% cures any problems I've had in the past.
  20. I

    Cooling fan options - Mechanical or Electric

    Try driving it on the hottest summer day in traffic with the aircon on and see how it fares ;)
Top Bottom