Search results

  1. I

    in the middle of changing out lug studs.........

    Screwdriver pops it off. (may need some persuasion with a hammer) There's a little cutout in the Upright where you can lever the cap off.
  2. I

    in the middle of changing out lug studs.........

    Toyota have a Division devoted to "complexity" ;) If there's an easy way and a hard way to do something they invent an even harder way!
  3. I

    in the middle of changing out lug studs.........

    Undo the Nut then press the Hub and bearings out of the upright, press the studs out press the new ones in then press the hub back in and fit a new nut from Toyota restake the nut after torquing it to it's spec (147 ft/lbs) and you're golden. (you did mention you liked the hard way)
  4. I

    in the middle of changing out lug studs.........

    Big cap on the back of the hub then a BIG nut (32 or 36mm from memory) and a big breaker bar.
  5. I

    Supra fag LOL

    404 funny not found
  6. I

    have youguys ever seen this pics?

    Have to laugh at the guys that are saying "I invented the DDP", unless you worked for TRD back in 87 NO YOU DIDN'T ;)
  7. I

    Engine making rattling noise

    <nodding> ;)
  8. I

    Engine making rattling noise

    Personally I wouldn't bother as it's a LOT of work to drop the crossmember but it's up to you it can/has been done with some success in the past.
  9. I

    Pushloc hose- who's using it??

    And this is why I switched to the AG Hose :D It still has the abrasion resistant sheath like the AQ hose but is nicer to work with, esp if you have to fit a hose on the car! AQ is ok once you get over -10.
  10. I

    Engine making rattling noise

    Auto or Manual?
  11. I

    MK3 supra parts from japan

    Guessing you mean my thread? ;) Don't do it all in one go it'll suck the smart right out of ya :runaway:
  12. I

    Pushloc hose- who's using it??

    Steve: Heat gun till it just changes colour then spray some window cleaner on the barb makes it easier ;)
  13. I

    MK3 supra parts from japan

    Pretty much just here, tried a few of the local forums but wasn't a good fit for me ;)
  14. I

    Pushloc hose- who's using it??

    I wouldn't use it if it's not fuel rated, have a look for Parker hose pretty sure it's a US company. Stuff I use if Multipurpose Hydraulic hose I get from an industrial hose supplier, the other one I've been using a lot of is an AlphaGoma product as it's easier than the Aeroquip stuff to get...
  15. I

    MK3 supra parts from japan

    < Northern Burbs here ;)
  16. I

    Engine making rattling noise

    This exactly.... :( Safer to pull Injector clips though.
  17. I

    MK3 supra parts from japan

    No probs ;) Which Burb? (PM me if you don't want it public)
  18. I

    Pushloc hose- who's using it??

    Pretty well forever, if you get fuel rated hose I can't see it being an issue ever.
  19. I

    MK3 supra parts from japan

    Melbourne Australia or Melbourne Florida?
  20. I

    DEI High-Temp Coating

    Have to say it freaked me out a bit ;) stopped in a couple of minutes and was fine, it was just where my WG is mounted it's the coolest part of the engine bay and not having any flow through it it just hadn't got hot enough to cure, the rest smoked like a bitch when I first fired it up.
Top Bottom