Search results

Going through the MS3pro manual, I see I need to set up the ignition. Can anyone lead me to some input numbers? Looks like I need to know the tooth angle btdc on the crank, and the input is rising edge, but with my LQ9 coils I need falling edge trigger for the coils. Standard 2jz 12...

Just about ready to install this. Harness just needs the shrink tube shrunk and installed on Saturday. I need to figure out what to do for crank/cam trigger angles and what settings to put in for the bosch wideband knock sensors. My AEM comes back from repair tomorrow, so once the Pro is...

Isnt it just a daugher card, firmware update?

Lookie what came today. This is Pro next to a regular MS alum case, about the same footprint, lower profile.

The 1j block is also alot shorter than a 2j. So stroking a 1j, would require hella short rods or custom pistons with a pin much closer to the rings. The displacement sounds nice, but at the cost of rod ratio and the potential to actually lose the tq your trying to gain. As hvyman said...

Not lift, just cam timing, iirc, its +/- 30%

Thanks for the link, unit seems compact, and priced right.

Sorry for the double post, i cant edit off my phone for some reason, but i havent tested 100% yet, but you should be able to use a gopro in the same manner, and watch live on the stereo your rear suspenion, or engine bay. I know the gopro 2 can do the wifi stuff, so you should be able to use...

So does my pinoeer headunit, im running the 930bt, it has just rca inputs, but my droid has hdmi output, so ill teather with an adpater cable. Sorry for the confusion.

Good call on the valet mode. I wonder if there is another alternative like using a switch to complete the clutch ground and it will always use the 2 step for the rev limit. I looked into the 7 inch tablets, but after spending the money on the double din, Ill use the droids hdmi output for a...

Im actually moving from Series 2, to the ms3pro. Way more feature packed and diys tech support is amazing. Pro comes with a registered version of tuner studio and megaview logger. My plan right now is to get the shadow dash app, and hdmi it to my double din stereo. Tuner studio, full...

I ordered 2 ms3pros and one ms2 yesterday for myslef and a couple buddys.

Sensors are cheap on Ebay. I used some extra Volvo sensors I had kickin around, from a 7/9 series, and even the 8 series cars.

Whats toyota charge for those? I used a couple banjo bolts and tapped the inside for my stud. Them bosch knock sensors came on alot of things, volvo, nissan, volkwagens, saab and others. Its a generic listen all bosch sensor. AEM has a post about the sensors and how to configure...

Depends on if the 1j and 2j have same cc combustion chamber too.

I stepped up a bit so I didnt have to open it back up. tranny, 2500 shipped (rebuilt with 900wtq warranty) adapter 200 (traded for labor and materials on a header build, 200 cost) clutch for and pivot stuff 100 triple disc 2000 slave and material for mod 100 forged 31 spline output shaft 150...

Im in for MS3Pro.

I added them there for collecting data. With AEM you can trim individual cyclinders, and with my intake having slightly different runner lengths, we want to be able to tune them.

Yep, check the gasket fitment. In the pic you can see all 6 ports are oval, and 2/5 ports are actually round on a 2j. I put mine togher and had a huge exhaust leak. Had to pull it out and weld up the port You can see the port mismatch from the exhaust on the gasket.

When I setup the clutch, I mocked up with a 1jz turbo clutch, and it worked with the 2jz exedy triple I bought. I havnt heard back from RogerDee yet. Ill shoot him an email. Its possible to use a push style pressure plate and run the GM internal slave as well, and no external mod will be...