Hey guys i think my rear wiper is the cause of my leaking hatch. anyone have a new rubber gasket for the wiper for sale? tried toyota they said it was discontinued.
hey guys,
just picked up a 91 with a 1j the old owner decided to remove the ac. I would like to put it back in and having a hard time sourcing a new condensor. anyone know where i can find one?
thanks.
riyad
hey guys
Im in the market for a set of coilovers for my 91 surpa. I am from nyc and am dealing with not the smoothest roads. Looking for a
comfortable sporty suspension. will be daily driven and taken to the track 1 or 2 times a year
any one have experience with fortune auto 500 coilovers...
Soo here is my situation, I have one Cam Position Sensor which was rebuilt last year with new o-rings and bearings. I believe the electronics are bad in it.
I have another CPS which runs the car fine but is leaking internally. Is it okay to swap the electronic internals from this leaking unit...
So i changed both doors on my car from a parts car and i noticed water comes right in the door thru the door handles and a little by the side mirror. i went to toyota looking for the gasket between the door handle and door but no luck it doesnt show it as a seperate part in the drawings or tsrm...
I have a jdm motor . it looks like egr block off plate is missing on the intake manifold (pic 1). .. the second picture shows that the second block off plate (red circle ) is already on there ..am i right in saying i only need a block off plate on intake manifold for egr block off also does the...
After learning about usdm ecus not working with jdm engines due to no egr i decided to check my ecu .. my car was originally a non-turbo automatic .I purchased it as a 5 speed with a jdm 7mgte. still working out the kinks of the swap from previous owner as i notice most of us are.. heres a...
cylinder 1 100psi
cylinder 2 120 psi
cylinder 3 110 psi
cylinder 4 117 psi
cylinder 5 110 psi
cylinder 6 110 psi
..decided to do a compression test to try to figure out if valvestem seals were causing blue smoke when shifting gears at high rpm or turbo seals and came up...
hey guys, I currently have 16" n/a mkiv rims on my 89 supra. i like the look of a bigger wheel in the back so I was thinking of putting 17" TT mkiv wheels in the rear, and keeping 16's up front. what would be the advantages /disadvantages to a setup like this . (ie fuel economy, handling, speedo...
So I recently found after finding oil leaking from my cps(cam position sensor) that there was no o-ring on it. So i ordered oring from driftmotion just wondering if this is how the cps, oring, and engine head are supposed to mate as its not sitting flush. Thanks
I just got my car back on the road after about 3 years and i see the antilock light is on . After searching i found that someone said it might be the speedsensor i looked under my tanny and found two connectors not connected im guessing reverse light and speed sensor.the problem i have is that...
Im finally coming to the end of my head gasket/rebuild on the supra after being out of the supra game for quite some time. I need to put insurance on the car and was thinking of antique insurance. Does anyone have antique insurance or can give me any recommendations as to which companies they...
so i got a bhg and i have been slowly putting everything back together. finally im close to the end of the project but im having some trouble reinstalling the intake manifold . the problem im having is figuring out how the wireharness was routed through it and where some connectors go. any tips...
so im in the middle of a rebuild/bhg repair. Yesterday i finally got the turbo in and this morning at 430 in the morning im thinking of what else i can knock out today and realize i didnt put oil on the turbo shaft prior to install:1zhelp:. is their anyway i can put oil without removing turbo...
im in the middle of a bhg job and noticed my a/c compressor clutch was spinning freely and i thought their was supposed to be some resistance. So i bought a used one from a member and his spins freely also...is the ac compressor clutch supposed to spin freely .
heres the thing i got a koyo radiator from a friend (belive it came from a 240) it would mount up but the right side hits the ac lines so is it possible to get stainless steel ac lines so i can reroute them and fit in the new radiator
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.