I asked a while ago if anybody had CAD drawings for flanges needed to make our own DP but nobody seemed to have any, so I made some of my own...
Attached to this post there is a zip file with drawings for Turbo(exhaust), cat(3" version) and the o2 sensor.
This should be enough to make your own...
This might be a stupid question but what is the point of a oil catch tank such as http://www.ridetech.se/Shop/Application/Article/ArtPreviewPage.php?Id=1026 ?
When should i mount one, at what level of modification?
I've got one of those HKS SSQV copies laying around in the garage, I'm thinking about mounting it on my 7M-GTE.
Is there a simple way to test it before I mount it?
It looks to be of pretty high quality...
I noticed tha my VSV's are loose and just hanging by their hoses in my enginebay.
See 17650 and 25860 in this picture http://www.cygnusx1.net/Supra/Library/EPC/291420/catalog.aspx?Figure=1708&Page=3
They are full of gunk/grease and I'm not shure how they are supposed to be mounted, or what a...
I'm going to the dragstrip this weekend to see what my Supra can do, but I can't decide which is the best way to launch with a manual tranny.
Should i rev it and drop the clutch or should I use the parking brake to build boost?
I always seem to spin to much or drop boost and get a crappy...
I hooked up a voltmeter to the Vf1 connection i the diag. connector today to check my lambda readings after I somehow managed to clean out my faulty AFM.
The car runs and pulls fine but the Vf1 reads 5.2 Volts at WOT, should I be alarmed or continue boosting?
It reads 2.5 Volts at cruise speed.
I was out boosting a couple days ago and a radiator hose broke (small one that supplies the turbo) and coolant sprayed out all over the engine bay.
The car is'nt running properly after that.
I dried everything out, esp. aruond the plugs.
The car seems to run fine when its cold and I rev it on...
My -91 T Manual trans. is a bit jerky when I release the throttle and when I accelerate again, most noticeable at low speeds.
There is also a "klunk" sound coming from the rear with every "jerk".
Any ideas? diff? bushings?
Which bends should i get for my DIY harddpipes?
I'm going to weld my own 2,5" hardpipes and I figure that someone must have done this before...
I'm doing both upper and lower pipe and the bends available are 30, 45, 60, 90 degrees. There is also a almost U bend available.
Anyone got the...
These sell for like $25 per meter (3,5 feet) and are 2,5" in diameter, they are flexible, stainless and very stiff.
The advantages (besides beeing cheap) are that you'll need a minimum of clamps because you can route the pipes as you install it.
The downsides I can see is that the inside is'nt...
How soon do you guys think that I would make use of a new bigger intercooler + hardpipes.
My current upgrades are:
Open airfilter.
Boch BOV
Single race cat.
Aftermarket exhuast
Apexi AVC-R
Retorqued head and stock gasket.
Should I get one next or should I save it for later...
Hi all!
I recently bought a MKIII T -91 (I used to own one five years ago (pre family/stationwagon:cry: ) but now I got me one to play with again:biglaugh: ).
It runs fine, no smoke, stable temp, oil looks fine, plugs OK but its loosing coolant and i cant figure out where.
I have to fill...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.