Reverse Light Switch Location on 87 Turbo 184 Trans
I am just trying to figure out WHERE the reverse switch is located on a 87 TURBO Manual 154 tranny? There USED to be a picture posted from 12-22-2010 05:50 PM from SUPRA RICH , but there is just an icon now with a X in it , and Chrome...
I'm sure in not the only person to have this problem , & its probably quite common, so here is my problem
When I select the AUTO fan speed on my 87 SUPRA . it always waited UNTILL the heater supply had warm water from the engine , BEFORE blowing. Now , it just starts right way ...
HI MDC MotorSports
your write up was fabulous on the CTR-26 MAKE IT LIVE.... i and alot of readers really appreciate what you did.
My question is , at the end of your blog.. you mentioned that you would do a follow up in 2011 with pictures or Videos ... its now 2016 and i was wondering...
ok,,, this is possible the weirdest post I have seen here so far... so here is the problem : >>>>>>
I have a 87 Turbo supra -- the issue is a radio that suddenly stopped working whenever I turned the ignition switch on and start the car.
background>> I've had this car for 27...
im needing 87' body side molding - drivers side -- aft of door., fwd of rear wheel.
also .. the carpet liner in back ... if you have it and its not faded horribly .
I am looking for a Cam Position Sensor for a 7M-GTE engine. the electrical connector and wires to in are FRIED and brittle and broken .!!!! HEAT is a killer on this stuff.
If ANYONE has knowledge or where abouts of where or whom to contact..with a good condition CAM POSTION SENOR...
yes... its stock and original. THe motor was rebuilt several year ago with a JASPER rebuild . The injectors were replaced at that time,& they only have 45K miles on them ..
THank you for the helpful and polite reply.
I have been trying to locate a SST for the fuel pressure, ( one with w/ a Banjo fitting to fit the connector.) but am having NO LUCK on line. if u have a source of where to get a Fuel pressure gage with a banjo fitting that will work, on Toyotas...
I think U r conr -fused jetjock.. ( AS U SAY!)
I was nicely asking for help to understand and service my car.. I love it very much and have taken excellent care for many years.
EVERYONE else on this site and on this post is always generous with wisdom , helpful and non sarcastic-...
YEs, I know !!!
and there aren't many CARS still left!! in this category... They are now classified as COLLECTORS I think- !!
how do u "jump the FP" as they say in the blog... what terminals to I connect or how is this done..? any links or pictures would certainly help - ie TSRM...
Hi
I have a 87 Turbo , that I have own since NEW .. yes I know its old ..!
OK here is my problem:
The car starts fine and wonderful whenever its cold .. even in winter -- so I know the Cold start injector is working and I m sure the cold start injector time switch is good as well...
thank u for the repsonse and help......... ill try it this weekend. I also check the VSV valve under the intake manifold.
as far as the fuel pump... thats located in teh tank... and that means a whole lotta work ..!! taking it down, then getting the FP out of it . i dont even know how to...
HI everyone
I have a nagging issue that is really puzzling me.. and i need someones help
Have an a 87 turbo that's Ive owned since new.. ( yes .. Im a true gear head!) with a difficult hot engine re-start problem ..... .
When i go to restart it after its run fvor 10 min or...
this is going to be ugly... i have a feeling .. 9 hours for a ASTM TOyota certified mechanic..?
the O-Rings for the intlet and outlet on the core itself.. i assume ???? or where do these special O rings go?
Is it necessayr to get into the A/C evaporator or break into the system...
OMG!!!!
that is the WORST event to do on this car..... and ive had mine for 25 years !! WHat O- Rings are you refering to ,, exactly ...????? i need to know this before even attempting this ...
Kevin
hi Dan\
the entire dash..??? cant it be removed working underneith and on the passendgier side? THe heat exchanger for the A/C is in the fiberglass white case thats visible when u remove the glove box. Istn the heater core in the middle, behind the temp control module and all the servo...
i wasnt trying to be a jerk or demanding for answers to my question , ... i looked at the posted TSRM link and there isn't any category for Heater,! ... only AC systems. Its not part of the cooling system either .. so that's why i asked if there was anything for the task of removing the...
HI
ok, i checked all the mentioned issues, ; heater valve, coolant level, ambient temp sensor, outside sensor ... \Then i grabbed the inlet and outlet heater hose in the firewall.. The inlet was HOT ... 175!!..However the outlet was Luke warm ... at best! 100 deg. SO i have a PLUGGED...
Thank you for the hot start answer .. i will check the fuel VSV per your instruction this weekend , if its not freezing outside again.
I wanted to get some better detail about the COLD air blowing all the time. There is hot water flowing in and out of the heater core. The VSV on the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.