Search results

  1. DeMoN2318

    Supra Jerks when stepping/letting go of gas...

    Hmmm...probably not the bov then. Fingers crossed on trans mount
  2. DeMoN2318

    Supra Jerks when stepping/letting go of gas...

    Even at lower rpm when out of boost?
  3. DeMoN2318

    Supra Jerks when stepping/letting go of gas...

    Does it do it in all gears? Only high rpm?
  4. DeMoN2318

    I can't find the 12 volt fuel pump mod

    Cut the yellow wire at the fuel pump resistor on the passenger fender
  5. DeMoN2318

    Looking for BIC 3'' DDP Rerouted?

    That's a bummer. Hopefully they are still in business...their products are of fantastic quality and when I was purchasing from them, the customer service was fantastic.
  6. DeMoN2318

    Front Lower Control Arm Bushing Removal Question.

    I had this same issue. I actually took the bottle jack from my press and put it between the ears of the LCA, then used washers as shims and a big socket that was the same size as the sleeve, then used the bottle jack to push out the sleeves slowly, adjusting the shims to make sure it was...
  7. DeMoN2318

    AFC NEO help

    Yes. That changes when it will switch from the low to high map
  8. DeMoN2318

    Throwing on a Driftmotion CT2657trim - Headgasket First??

    You can just cut the yellow wire at the fuel pump relay harness and get the same effect as the 12V mod. http://supraforums.com/forum/showthread.php?317271-12v-constant http://supraforums.com/forum/showthread.php?317247-where-can-i-find-the-pinout
  9. DeMoN2318

    Official CD009 to Mkiii group buy

    Its not dead...
  10. DeMoN2318

    ***SM member 1/4 mi. times list***

    Made the List!!! MK3 with a 7MGTE! May 15 Drag Car by Justin Paulus, on Flickr May 15 Drag Slip by Justin Paulus, on Flickr Lex AFM, 550s, stock CT26, 3inch Exhaust, FMIC, NEO, ACT Extreme PP and 6 puck
  11. DeMoN2318

    Rear wheel Bearing

    I can't remember exactly, but I'm pretty sure its open. I remember there being an inner race I could remove and get to the ball bearings
  12. DeMoN2318

    Rear wheel Bearing

    I had to get a special puller tool...
  13. DeMoN2318

    Throwing on a Driftmotion CT2657trim - Headgasket First??

    You need to get a specific tap, its called a bottom tap I think, DM might sell them. About 1000 long qtips, brake cleaner, and a can of compressed air
  14. DeMoN2318

    Throwing on a Driftmotion CT2657trim - Headgasket First??

    It would take a lot of heat, sustained heat, to warp and anneal an iron block...
  15. DeMoN2318

    Throwing on a Driftmotion CT2657trim - Headgasket First??

    So if you run the straight edge and it is slightly warped...are you gonna pull the motor and have it decked? Or are you just going to straight edge it for peace of mind...
  16. DeMoN2318

    Throwing on a Driftmotion CT2657trim - Headgasket First??

    If you are using studs, please make sure you clean the holes out super super good. Bottom tap, toothpick, Q-tip, everything you can think of...just make sure there is no junk at the bottom of the hole. I would hate to see a thread in a few weeks of you saying you cracked your block and are...