Search results

Is that sanding dust all over the garage floor?

That's actually very good for a stock CT26 @ 10.5 psi. I guess the P&P head is really working.

Looking back I wish I would have stayed with the stock set up with an upgraded CT26. I'm not shooting for massive rwhp. I'd be perfectly happy with 350-400rwhp & rwtq. But back them I scored a T4 garrett 60trim at a good price. That began the start of my T4 quest. If wish that I knew what I...

I was out tuning closed loop operation today. Getting things dialed in as much as possible. I'll get to open loop soon enough.

Why you crack up on thread he did about result of smog? This busness is all to serious at this right now time.

If you're going to have your dash out of the car then you need to try to do it on your own. Vinyl fabric, contact cement, heat gun & exacto knife. There's tons of videos on youtube of how to do this. Give it a try. You'll feel accomplished once you do this on your own. I plan on doing my...

i no understand why you no want kick out. you should able to post on results on smog result. i see no way of how they wont let post you of them.

Aren't you supposed to hand him your drivers license and CC permit at the same time? There's no need to verbally warn a police officer you have a firearm on you. When he receives the permit he'll know there's a firearm in the vehicle. When you calmly tell him "there is a firearm in the vehicle...

Sounds cool. How much is a little bit?

Ok, I took off the manual boost controller. I'm going to run off the wastegate spring which is rated at 12psi. I've set the fuel pressure back down to a "normal" 38psi with vacuum source disconnected. I'm going to retune the MAPECU and see if I can keep things under fuel cut at that fuel...

Injector cleaning usually runs about $20 a pop. I plopped my fuel pump in a bucket of water, connected it, and tested the flow. I was worried about a spark igniting a bucket fuel of fuel, so I opted for water. Dried everything with compressed air, and dowsed it with WD40 after the test...

Pea gravel and a couple of gallons of acetone/thinner. Some use muriatic acid. Strap it to your tractor wheel, jack up the rear of tractor, and let it go for a good while. What? Don't have a tractor. Then you'd have to do it by hand. http://www.youtube.com/watch?v=eVZvjdQT3ks Or take...

There's a guy here selling some probe forged slugs for cheap in the for sale section. They've gotta be better than stock castings.

Damn impressive for a "junkyard" turbo at 20psi. And for $150!? Did you have it freshened up, or ran it just as you received it? I wish I had it in me to get one and fab up the bits and pieces to make it fit/work. I just got a turbo that I could plop in and bolt up everything as the old one...

I was just wondering is it bad advice to ask someone to perform a leak down test? Because every time I suggest it nobody ever does it.

So did you end up getting these injectors? I see in your sig you list them as part of your upgrades. If you did, who was the supplier and what was the cost of each injector.

I thought that looked familiar. I saw that pop out when I changed my power steering pump pressure line. Goes inside the power steering pump. 44330 valve. http://www.cygnusx1.net/Supra/Library/EPC/291210/catalog.aspx?F=4502&P=1

That is a possibility. There are honest mechanics out there. They're are far and few between though. I've met some along the way, but I wrench myself. I've saved myself thousands of dollars over the years.

Mods - slow66 hasn't even been on Supramania.com in over three years. Will somebody appoint someone to update this list please?

Me too. That's why he's ignoring my questions about who initialy installed the front main seal. More than likely his mechanic did cause it doesn't sound like he knows much about mechanics. He took it back to his mechanic about the leak. Mechanic sees that the front main seal is faulty for...