Search results

Piston's are a precision part, they have a very slight tapper to them,they are a little larger at the botton. Chance's of doing a precision sand blasting is very slim to none. Forge piston need more piston to wall clearance than cast, because of expansion. So you need to measure the piston skirt...

Does any one how to wire head light squirters on a car that didn't have them to begin with? I only want tham to work went the head lights are up or on, I don't want them to work like the early mkiii's, they work when you hit the button. Is there a relay or a hot circut when the lights are up or...

I'm hooking up a Greddy Ultimate on my ninety Supra. I'm looking for a wiring diagram for the E.C.U. harness, I need to know which color wire recieves which signal, R.P.M ground, power, A.F.M. timming, e.t.c. I know there's pin location chart, but, it would be a heck alot easier if it went by...

God Bless you Thanks!

Tenth of my time: worth my time for some bad humor, yeah seriously I v'e never seen it here, my it's because I have drawer full penatrants. No, really Who sells it In Ca?? Auto parts stores?? Walmart?? Really though, I learned something, today,..thanks! Jetjock!

WoW!! I learned a lot,, "there's an internet now?? "HuuuH" "Penetrants" you mean as in porn?? I never heard of the "Blaster" here in California but there is a lot porn here. "Calipornia."

Yes It does,... Thank you!! please ignore my "p.M." to you. You wrote this at the same time I was p.m.ing you.

How about telling the audience what "P.B. blaster" is.. for those of us that don't know. Is this a product that is national, regional or is it world wide? Is it another name for Liqiud Wrench? Apparently, I've been sleeping or It's not sold out here.

I understand the majority of this. I guess I'm a still not sure what your talking about on your first sentence. "You don't have to, if you drill out the restriction inside of it" I can't tell if your talking about the "J' tube or the plusation damper (since I was asking about the plusation...

So, from what I can tell by reading this. This is base presure at idle, by setting the base presure, this should be all I need to do since the regulator is a 1:1 ratio. According to the picture in the fourth thread, a gauge reading 60 p.s.i should more than enough.

v= vaccum s=switching v=valve

So the way it sounds now, this mod isn't even needed unless you tune your car, so what would happed if you just jump the two wires like "j"dub" did while your tunning and go back to nine volts while driving normaly, or did I miss the point? I know stock runs at nine then goes to 12 volts. Walbro...

Damm You got that right, let's make this a sticky To change the needles, I believe you need to take them off, sand the current paint off, then paint desired color. Only paint the backside of the needle, NOT THE FRONT. How do you remove the needles? __________________

As for your pulsation dampener, you do not need to take it out but if you would like to do so, just run a hose from the fuel line to the fuel feed line at the bottom of the block I don't get it, if you don't have to remove the pulsation dampener then why are people doing it? It must serve...

Great write up! I need to do the samething.

What's the advantage of have the Greddy control timming verse The Stock E.C.U.? What are some of the important tweeks that you should do on a Piggyback? A.F.R. for one, what are the others?? Timming,boost?

Sawblade weight: 25.07 that included the shipping box, this box was from aftermarket wheels so, it wasn't an over size box or anything like that. with out the box I'd say about 24 l.b.s.

You like blades?? buy mine...........

Hey "87" Soup Great work!! I really like the "FC3S" Mazda "RX' 7 shirt, that's cool design. Is it Possible to place that on the back of the shirt and slightly stretch it? Or maybe leave it, it's hard for me to tell, anyways centered and evenly proportioned. Can That be done with a "89"- (or...

"Supra" Want to race from a roll" Love it!!