Search results

  1. A

    Stinger thread....

    I pulled enough slack on the Stinger harness that I can mount it in the OEM location or below the dash like the MK4 Supras. I got all of the wires connected up. Im just missing a few 10gauge butt connectors and 10-16gauge female spade connectors to neatly finish my relay installation. I...
  2. A

    Stinger thread....

    I got my starter all wired up, was pretty straight forward. (white/blk wire off ignition switch pigtail) I fabbed some crude brackets to hold the coilpacks in place in the spark plug valley. Im wrapping my harness now, and I will wire in two relays one for igniter and coils on stinger, and...
  3. A

    2jzge

    I am putting a 2JZGE-T in my 87 right now...... I built it for about 500rwhp.
  4. A

    Stinger Basics for a 2JZGE

    I found the oem fuel pump wire. (Black/Red #2 wire going to Fuel Pump Relay on right side shock tower) I will wire in that wire into the relay according to p16 of the stinger manual, then assign it an Aux Output control. (It's also in the G1 harness center pin #7 in the drivers kick panel...
  5. A

    Stinger Basics for a 2JZGE

    Just waiting on my GM-IAT delivery to finish wiring last sensor. I have wired up so far... CPS, Temp Sensor, Injectors 1&6, 2&5, 3&4 (using Primary Inj wires pinouts #23, #11, and sec/prim Inj #12), IS300 Igniter, IS300 coil packs. I have grounded the EMS, and connected both the red + wire...
  6. A

    Stinger Basics for a 2JZGE

    So I am about to install from scratch this Stinger on my 2JZGE swap. I would like a few tips from those whom have had first hand experience with the stinger wire up as all I have to assist me is page 11 of the PDF :). I have already set the motor to TDC verified that the cams and crank...
  7. A

    Stinger thread....

    Hmm, I cant visualize that.... right now I have a 10gauge switched 12v coming from fuse box in engine bay and that goes to the Big square plug input next to ECU under dash. I can only assume that somewhere in the stock harness a signal of some sort is sent to the starter solenoid what...
  8. A

    Stinger thread....

    cool got it thanks..... what about the starter? did you have to integrate that single blue wire square plug from the engine harness? I a mnot sure if that somehow plays a role in the starter relay? Know what plug Im talkin about? you kinda always break your wrist tryin to get it out :)
  9. A

    My supra replacement..... An MKIV supra sedan.....

    I owned two IS300's for 9yrs. Congrats, you are gonna enjoy that car!
  10. A

    Stinger thread....

    Thanks, ideally i would like to use my is300 coilpacks and is300 igniter. (Newer parts) i will see if i can identify details around the vvti components and how they are triggered. But will they be compatible with the 7mgte cps, or doea that hook up independently to the stinger EDIT: After...
  11. A

    Stinger thread....

    I am planning my Stinger installation as I can not waste anymore precious summer hours tinkering with splicing factory wires. Although I like the cool colors in the 100+ pin toyota harness and am fairly decent at wiring, I need my 2JZGE-T running and on the road. I would love some advice...
  12. A

    2jzge

    Then either way you are going with forged internals for the bottom end and not OEM GTE replacements? correct? As I'm sure you already know, the head design is different.
  13. A

    2JZ into MA70 Swap Pics etc

    Dr. Tweak I also sent you an email....
  14. A

    2JZ/1UZ wiring into MK3

    I am actually using an older 2JZ Aristo swap to asssit me as well. (Satan's post here ... http://www.supramania.com/forums/showthread.php?59181-Wiring-Peer-Review-Aristo-ECU-Harness-in-91&highlight=wiring+peer ) I am going to make it simple and clean and outline the BASIC and minimal wires...
  15. A

    2JZ/1UZ wiring into MK3

    So finally made some time to work on the Supra. Viper (Bryan) was kind enough to return my call and we went through his original document. I believe I have most of what I need sorted out. I now have a small issue of when I turn the key, the starter sound like someone hit it once with a...
  16. A

    Spring Restoration - Project old school MK3 revival

    So all my lines and accessories are mow connected. I have also replaced the rusty header panel frame with a cleaned up and primered replacement. I also took the grinder to the bumper and removed all the rust and then lightly filled and sanded it then also primered it. Now I am just trying to...
  17. A

    2JZ/1UZ wiring into MK3

    Pictures as requested by Bryan (Viper) Inside Dash
  18. A

    2JZ-GE high power

    I just finished installing my swapped 2JZGE wit ha PT61 Turbo Kit. Im doing wiring now. should be done in a few days if weather holds out.
  19. A

    2jzge

    OBD1 GE motor share similar if not identical internals composition (compression and ring spacing is different, but pistions are just as strong, rods can be identical to GTE in some cases)..... 93-95 GE's have been documented to run 600 rwhp on pump gas. You will spend a lot of $$$...
  20. A

    2JZ/1UZ wiring into MK3

    So I am pretty much done with 99% of the physical work in my SC300-T swap. I have been using a lot of information posted on http://www.1uzsupra.com Granted the 2JZ and 1UZ are different motors but they both integrate very similarly into the SC300/400 chassis and harnesses so forth. I have...