Ryan's 92 build thread aka NashMan

[NashMan]

well not much done today since i ran out of mig gas and straight argon is just shitty to weld with

but here is pick of my batt relocation breakers and fuel pump controller and bottle

and he is my shitty down pipe it fit's but she is pain in the ass and i pickup a china steel flex joint and while welding the pools of steel would explode not very fun to weld at all fuck you chins cheep steel

 

[NashMan]

mellon launcher 2000 gtr lol

i have to slight twist to one cut but meh she is good to go

next is dump tube

 

[Mk3runner]

looking good!

 

[NashMan]

well my lipp fuel rail has some pock marks aka casting defects were the injetor o rings go so i will be given them a call and try to get replacement

 

[Muzy]

Looking good Ryan, These cars are 2 rich for me. Selling all my Sup stuff. Will keep up on your progress though. Like your work. muzy

 

[NashMan]

^ given up all ready boooo

 

[NashMan]

more pic of exhaust just need to get some clips and springs for my muffler

but here some nice pic



and thanks million to Mr mike for giving me a hand

the down pipe will be re-made later since it pretty much remove car to get down pipe out


wiring should start tomorrow and maybe running by the end of this mouth hope fully

 

[NashMan]

i hate wrapping



wet then heat gun makes for tight steel light wrap best way to do it did the same with my down pipe too

done

sealed

pic of me

 

[NashMan]

well got some stuff done the oil dip stick was a pain int he ass to install so bloody tight and one of my turbo hot side bolt is tolota bitch to tighten grrrr

zex fully and inter cooler purg installed just have to wire it in

oil dip stick i know it's gay but it works

perfect fit lol

thermostat spacer i might be making if there is interest

the idea is you can pull you front timing cover off with out taken the thermostat housing off and have extra tap ports for gauges

 

[tekdeus]

Nice Ryan. You might want to heat wrap your speedo cable, mine broke shortly after my turbo kit install having the downpipe so close to it. I also notice my dash and interior is way hotter with the downpipe so close the firewall.

 

[NashMan]

she wrapped pretty far down and it is new cable too so i should be ok my last car use to be closer and used to make the floor stuiped hot


but i do have wrap for miss wires and such but that least of my censers right now need to make ti run


but thanks brad hope to see yea in van

 

[NashMan]

well got some stuff done today

just have to wire all this crap in and that not all of it ether grrr oh well

 

[NashMan]

well got some stuff done wireing is so much fun

 

[GrimJack]

That's a wicked mounting location for the microtech... does the top fit back on the stock ECU case?

 

[NashMan]

yaa but going to leave it open so it has more air flow thou

well back to the mess of wire's i got going lol

 

[OneJArpus]

I love the way your car is coming together nash. great work!

 

[arizzle]

cars coming along really nice! is it going to be up and running for pnw?

 

[NashMan]

i don't know lots of work no help lately


right now i am stuck and trying to wire in my pps to work but the tsrm is use less because it does not give me the pin out on my speed sensore

 

[NashMan]

well figured out the pin out of all the stuff i was after


i have filter for the hallfect sesore now i hope it will work good so we will see it's for the avcr

and i pick up a isc vavle from a for 98 ford there so bloody small i like it pic of whati am talking about

http://www.ford-trucks.com/forums/136188-idle-air-control-valve.html

 

[NashMan]

well got a bunch of stuff done hope to have ti fired up before Friday


i used a ford aicv from 2000 ford torues/truck since my ecu does not work with the toyota one

and here is a small link to them

http://www.ford-trucks.com/forums/136188-idle-air-control-valve.html


here is what i did to make it work it was rather easy and simple and cost me peanuts as well 10 bucks for the valve from the weacker

drill a small hole for vent and drilled out the old vent and expoites the brass fitting in the rest is pretty self expand atory