Search results

I dont know if you guys are aware of this but we made a run of Stainless steel Targa bars a few years ago and they were a hit. These are a lightweight two piece design, one for each side that tie the front windshield frame to the rear roof using the factory targa mounting locations and hardware...

I have a bunch of vids from the last few years so i figure you guys might enjoy them. Keep an eye out here as we will be adding more vids as we make them. First off here is a link to the BIC Performance Youtube channel: http://www.youtube.com/user/BICperformance Here is a few of my...

The BIC Performance shop car finally eclipsed 500 WHP... We recently removed the T61 and installed a Borg Warner 88-75 (63mm compressor) with a twin scroll turbine housing and we are extremly pleased with the results of this turbo, it flows 78+ lbs/min but spools like a 61mm. The basic...

Well its time for the monthly 604, Lower Mainland Supra meet and greet. There have been a few changes at the shop and we are moving in a new direction and figured we would kick it off with a BBQ and have it at the BIC Performance shop. We will have the grill going and make some Juicy BBQ burgers...

Incase you havent seen this yet... Click on this link: http://www.supramania.com/forums/showthread.php?124221-Calling-out-you-Gutt-less-Torque-less-1JZ-s-!!!

This is an official callout for any 1jz's in North America to come down to the Pacific Northwest Supra Nationals in B.C, Canada on July 16th-18th and beat the BIC Performance.com Mk3 Supra in the 1jz classes. There is drag racing on Friday 16th and the horsepower dyno competition on the 17th. No...

Any one her used one of these yet?. These look to be very promising heavy duty turbo's. Full race swears by these turbo's and tested one of the BW 61mm turbo's against a Garret GT35R and it out spooled it and made more TQ at the same boost, not bad for a large shaft journal bearing turbo!! The...

BIC Performance is an official Haltech dealer and it is our EMS of choice. I have the New Platinum Sport 2000 ECU in my own car and have installed and tuned many of our customers cars. There is a P&P harness available for the 2jzgte MK4 Supra using the PS 2000 EMS, and now recently released a...

I thought we should have a Haltech specific thread here so if you guys have any questions or experience with Haltech EMS's it will all be in one place. BIC Performance is an official Haltech dealer and it is our EMS of choice. I have the New Platinum Sport 2000 ECU in my own car and have...

Well we have been busy here at the shop and figured its about time we post some of our shop projects. Here is the most recent build. The goals are 475+ on pump gas and 600 on high boost (water meth) -87 MK3 -Rebuilt 2jzgte -Crower 264 cams -BIC Performance single turbo kit, DBB T67, .68 A/R...

Just finished a 1jz swap into an 86, and put a 89 turbo tach into it. The tach reads off by a few thousand RPMs. I remember some sort of resistor mod to make it read correctly. Any one know it off hand?

I recently installed a brand new DBB T67 (garret) turbo on a 2jz. I am running a -4AN feed line with a .030 restrictor in the oil inlet, the drain is -10AN with a 45* off the bottom of the turbo and a 45* on the block. There is no kinks or sharp bends in the drain line. Now once the car is...

Quick question. My fabricator installed an HKS FCD on a 1jz mk3, just wondering what you guys have the setting switch at ?. There werent any settings listed for the 1jz only the mk4 or 7M. We tried 7 and 9 but still hit FC.

I just picked up some brand new wholesale exhaust systems and headers from a closed down shop. The brand is Alphawerks, and they are all full 304 SS 2.5" mandrel bent and really nice parts. The mufflers also include a silencer. Would be really nice for your daily driver or you girl friends or...

Anyone know the thread size of the low pressure power steering fitting, it threads into the rack and there is a short 90* pipe on it. Its smaller than a 18x 1.5 but larger than the standard PS fitting thread. Also if anyone has a spare one I need one, let me know.

I have repaired a few rear subframes now due to cracking including my own, and I thought that I could offer pre cut plates and reinforcement bars to you guys. You would have to weld them on your selves or take it to a welder/ shop. For anyone local here I can do the welding and install of the...

I figure I would post some new results of recent work into the shop car. One of these days I will make a build thread with all the details but for now this will do. I will get some the time slip and some vids posted up soon. Here is a basic rundown of the car: -1jzgte swap -USDM 2jz...

Just wonding what is the reccomended single plate clutch for 600-700 whp , on a 2j, T67, cams, full fuel system. I am thinking about going with a RPS stage 3 with a CYNERGY flywheel. Not interested in a twin or tripple plate. For a MK4, not MK3

I have been fighting these JZ coils/ ignition on every car that we tune here. No we all know that JZ coils like to crack at the screw area where it mounts to the bracket and under the plug boot, which causes missfire at higher boost. When ever we get to the dyno, and try to run 17-20 psi we get...

Now that i have your attention....I know most of you guys that have the JDM Recaro seats have areas that have been worn through, or faded and damaged from the sun, myself included. My cousin runs an auto upholstery shop and he had repaired my passenger seat bolster before, using the material...