Search results

Installing new injectors with evo1 clips. Are the wires polor sensitive? Or can I solder them in however?

Blower motor is working. Hardly any air coming out of vents. When fan set to resirc it gets loud. Any ideas?

88 7mgte. Flushed coolant this past summer and added prestone and distilled water. Had gurgling in my heater core but got the air bubbles out. Its getting cold here in alaska and the supra is the daily driver. My hvac door works, my vaccum operated coolant block off actuator near the firewall...

I had these cleaned at witchhunter performance. (Fast service and reasonably priced!) Came back with larger pintle caps. Would this cause a problem? How does my flow sheet look? thanks guys.

Did one on my dads 90 7mge with 201,xxx miles cyl 1: 210psi cyl 2: 210psi cyl 3: 155psi cyl 4: 150psi cyl 5: 205psi cyl 6: 210psi there was a bunch of oil from when i removed the spark plugs. Thinking thats why the cylinders are in the 200's. Whats stock psi for the 7mge? And what...

how can i tell the difference? I already have a bhg on the thing but she blows some blue smoke and uses about a 1-2 quart every 3000. I obviously cannot do a compression test with a bhg at the momment, whats another way? I was thinking a leak down test, but that would not work either with my...

Hey guys, I used the starter method to get the harmonic balancer bolt off and guess what, it broke, lol. so, my question is has anyone experenced this before? Whats the best possible outcome? tips, tricks, tools needed to extract that bolt?

Hello, Im going to replace me front main and oil pump driveshaft seal here in a couple weeks and this is what im buying. 1.90311-52003 seal, fm list 90080-31022 seal, op drive list 11312-42010 gasket,cover rh list 11313-42020 gasket,cover lh list 16124-42020 gasket, water pump list...

hello fellow supramania members! I have been chasing a oil leak near the front of my engine now for about 2 weeks. It leaks about the diameter of a coffee can on the cement. I checked my valve cover gaskets, my cam seals, my oil filter, I have a very small leak from my oil cooler lines, (very...

at idle it outputs 11.85 vdc with my lights on. i give it some throttle and it goes back to around 14. normal? my lights dim when i slow to a stop also. any input?

So im getting the code 31. Im searching for a used good one in spec with the tsrm. If i just buy the shell with no little black box on top is that sufficent? Or does the little black box on top of the afm go bad as well?

I bought part of the passenger side rear fender from 'CrazySupra' on the forums (real nice guy to deal with) which included part of the inner fender. My question is is it possible to remove the outer skin from the inner fender well? I would not like to replace part of the inner fender well, just...

When im at a complete stop in my 88 t 5 speed, when i push my brake pedal slightly i feel a vibration in my shifter? its weird. never when im slowing down, just when im at a complete stop. any help?

Hey guys, Little back ground with my car, 88 turbo 5 speed with 3 inch exhaust, intake, arp bolts with toyota gasket, new clutch and what not. Since i bought this thing 2 years ago, its been hard to start when it was cold. It would take aleast 5 seconds to start, sometimes twice. Never...

Im in Harrison Twp, have a 88t. Just wondering where everyone is at!

Went to the exhaust shop today, had them cut of the forward part of the cat and install a 3" straight pipe all the way back. I had them use the same flange that bolts to the downpipe, all for $156 out the door. It sounds good and def woke up my car! I guess my question is, will a aftermarket...

While doing my clutch, i seemed to brake the knock sensor by the starter when i was doing my clutch. The cable and connector did not snap, just the actual sensor its self. My question is, what are the effects on drivability and would driving it damage my engine? I wouldnt mind if it hurt the...

Installed new clutch disc, pressure plate, and throw out bearing on my 88t. Put new bolts in for pressure plate torqed to 14 ftlbs. When car back together, it would not go into gear while started. I put it on jacks, clutch depressed in 1st gear and started her up. The tires were spinning with...

Do i have to remove the downpipe to remove my transmission? I would rather not if i didnt have to. I left my tsrm at work.

my stock 88 turbo needs a new clutch. Its my daily driver while my wife has the truck. My question is should i just get a oem clutch if my power goals are around 300 eventually? I do not plan on upgrading anything as of rite now for power wise (I have a baby on the way) but do not want to get...