Search results

  1. TurboStreetCar

    Re-dynoed on a mustang dyno last week

    Damn man, nice driving!
  2. TurboStreetCar

    This can't Be Normal

    Well if your pumping the brakes rapidly it could cause that effect as the manifold has to keep the reserve in the booster at low pressure. Your basically creating a vacuum leak as you press the brakes.
  3. TurboStreetCar

    Compression Woes

    If it were my motor, i would pull it and do a full rebuild rather then playing with unknowns and someone elses mistakes. This is what i did with my engine. The block would have to be VERY warped to cause such a leak with a stock gasket. Ive seen composite gaskets seal some nasty looking...
  4. TurboStreetCar

    here's a broke sub frame.

    Ill be doing this come summer time. Nice work Bryan.
  5. TurboStreetCar

    Re-dynoed on a mustang dyno last week

    Damn man impressive, what kind of 60's with that launch?
  6. TurboStreetCar

    Compression Woes

    Are you sure you have the cam timing correct? If you put in oil and it didnt change it would be time to rebuild the entire engine. No compression is a rings and/or piston problem assuming cam timing is correct. The block would have to be REALLY warped to lose that much compression. Just to make...
  7. TurboStreetCar

    my auto supra stalls when i dont touch the gas

    I thought i was too when i read your post. :biglaugh: :aigo:
  8. TurboStreetCar

    Pertaining to gaskets

    That could definitely be an issue.
  9. TurboStreetCar

    Cps hard wiring

    For the CPS connector im using a MSD connector. Its very easy to crip and its a very nice quality connector. It can be had here http://www.summitracing.com/parts/MSD-8181/ Very nice piece.
  10. TurboStreetCar

    Why don't my rpms drop when i push in the clutch on my car? suggestions?

    Again? What changed to make it stop the first time?
  11. TurboStreetCar

    2400 miles of bliss!!!

    Where you getting the hood struts from? Toyota?
  12. TurboStreetCar

    Which way is better in a race

    That doesnt make sence. Shifting at 6500rpm slow or fast the bearing is still spinning 6500rpm.
  13. TurboStreetCar

    almost hit 600rwhp last night

    Well get some fuel to this thing and see what it does!
  14. TurboStreetCar

    Re-dynoed on a mustang dyno last week

    Exellent work with that car. What size rubber on the back?
  15. TurboStreetCar

    Which way is better in a race

    :biglaugh: And far from faster.
  16. TurboStreetCar

    my auto supra stalls when i dont touch the gas

    Shit, proof read failure. I'm posting with my iPhone. It corrects words sometimes and sometimes fucks up. Edited.
  17. TurboStreetCar

    my auto supra stalls when i dont touch the gas

    Check for codes, if you slowly let off the gas does it try to idle at allot just completely die?The throttle plate is for the most part completely closed and idle airflow is almost entirely dependent on the ISC valve. You can test it using the tsrm procedure.
  18. TurboStreetCar

    Which way is better in a race

    Very hard on transmission and clutch. Not worth it for the maybe tenth youll make up in the quarter.
  19. TurboStreetCar

    mp t70 or dm67

    Modular Turbo is a Master Power turbo SM authorized dealer. Why is the Master Power going to break after a little while? Not steering buiness away from Aaron, I'm a customer of his, but there is a vendor for Master Power on the forum.
  20. TurboStreetCar

    alternator wire help asap please!!!!

    pictures would help. Can you solder it back together? Or use a crimp connector?
Top Bottom