Search results

John - Seth told me in a PM. I don't want to make his cost public, but it is so reasonable that I will hand over the cost myself if we can't pool the funds together. Actually, he just pm'd me to go ahead and post the amount. it is 200.00 plus the core. So that is what we are looking at. I...

Seth - Thank you, I was planning on running the stock set up for starters, but I would definatly take a FFIM if you are willing to build one. I would just plan on building the inteercoolerpiping and intecooler differently. The lack of funding was going to make me use a stock manifold. How much...

Box came from Summit Racing. Not a bad kit for the money.

Here is a pic of the turbo donated by Sean. Thanks again to Sean from Titan for stepping up in a big way anf helping us out with a really nice turbo. Garrett gt4088 Here is a pic of the battery box purchased with donated money. This kit came with all the hardware and a bunch of...

Driftmotion in the Vendor section!

Looking good my friend! Can't wait to get our two cars together this summer!

Boostedfloto - Did you buy that scraper from me or directly from Kevin? I had several people complain of having to grind the scraper also. It turned out that they ordered a 6m scraper to install on a 7m crank. Kevin makes the early and late model crank scrapers. if you purchased the 6m crank...

When your not using a torque plate, I advise to run an extra half a thou clearance. This will make up for any 2 sided tightening of the bore once you torque the head.

Ehh, bee sting vrs sledgehammer.

Yes - We need springs. The eibachs that are on there now had been cut down an additional 1.5 inches by the previous owner. Doward - That would be perfect! P5150 - I had thought of that once myself, but for some reason the universal is a wee bit more money than the 87-88 unit. I can get a...

I am running the Greddy/Trust mk3 intercooler kit. It is as nice a fit as I have seen. Not including the Cartech of course.

The 87 harness would be just fine. I have not heard any real issues or differences between the early and late model part numbers of the AEM. The MAP would be mounted near the rear of the intake manifold. The IAT may at first be mounted in the charge pipe just over the plug wires. Later, if a...

Maybe two of them?? I'm not afraid of my own turbo's

The 3406C Cat motor in my excavator has nearly 50k hours on it. The Detroit 4-71 in my old Hein Werner excavator broke the hour meter 15 years ago at 35,000 hours. It still runs stong and has never broke once in the 18 years I have owned it. Oil changes only. The 6V-92T in a dump truck we had...

Hey everyone! I was hoping to be giving away some money, but there is always next year. Thanks to everyone who showed up and raced. Also thanks to everyone who put up money for the pot. Hope to have all of you for next year too. The money really was never a "pot", meaning it really was not...

How much are you guys paying for Redline? I don't understand all the talk about using another oil, just because the one you really want, is too expensive. It is about 40 bucks to fill a 7m with Redline. The difference between Redline, and the next best, can not be more than the cost of a bag of...

Redline - anything else is just nut sack grease. I have 5 cases in my garage and it goes in everthing right down to my lawn mower. I would cook with it if it did not taste so bad.

Hey Bud, thanks for your help! The timing belt will be a must, the one on there now is really bad. The wire harness is a disaster. I will prob lean to a AEM EMS and will use a GM 5 bar map sensor and the IAT. Sean sent us a GT4088 joural bearing garrett with a garrett .72 comp., and a .81...

Well spring is coming and I am not going to make it to TX, so I will spend some long over due time on the build. This weekend I will get a good round of photo's taken and start to hash out some more plans. Need to go buy a battery to mount into the new rear battery mount kit I have. Need to...

These TMS 7m pistons are going to be a go! I have purchased the exclusive right to market the first batch of pistons and will be the only person you can get them from. They will be the same forging as originally posted including double forced pin oiling and accum. groove. - 1mm, 1.2mm...