Search results

With or without you in the car?

I think you're mistaking 7M and JZ series engines. The record power from a stock 7M block was done by Xman with a brand new factory block, and it was 750hp. Duane and Mibrum are the highest HP 7M's, but they are both fully built.

Oh yeah, lots and lots of corn burners running. IIRC, that maroon Camaro I ran was on corn, too. I used 3 tanks of gas in 3 days, and I only raced the first half of the last day! WOOT well-spent money :D

AFR's went stupid lean, but that's because whenever you have a misfire, lots of oxygen gets thrown into the exhaust which fools the AF sensor. I wish you the best of luck, Adam!

Lol, no worries Kyle. Each cruise session runs ~20-30 minutes bt when they end one, you can just hop back in line and get back on the track. The most I saw at once (when on the track) was 10 cars, but 3.1 miles can hold a lot of cars- I'd guess 20-40 cars at once. I think the final count of...

Hmm, sounds a lot like when was blowing out the spark last weekend. On wastegate (18psi) it was fine, but when I tried to bump it up to 24/25 it would sputter and backfire and break up badly. Gapped the pulgs down to .023 from the .44 they were at and BAM! no more misfire! I am also running the...

Rules of Powercruise: Car must pass tech (battery held down, brake lights work, tires have tread. No Stopping No Drifting No Burnouts Speed limit of 100mph (loosely enforced, I did 150 on the front straight) BAC of 0.0 -that is all-

Adam, I like to set my SPR setting about 4-5 psi below what my target boost is so I get the better spool, but not any of the oscillations (or less than there could be)

Brainerd International Raceway in MN. It will be happening next year again, I'll post up when the date gets set. This is something I would ship my car to just so I could do it again!

I'd say a better question would be "How do I get XXXrwhp from my 7M-GTE" Set a goal and then start gathering information to try to achieve that goal. It's a much better plan than just cranking up the boost with stock stuff and wondering why it blew up. Also, don't feel singled out, this...

Just by showing them the diagam the Funkycheese made up should be enough... I'll ceck to see if I have any pics saved of that wiring, though. Edit: I looked but I don't think I have it loaded to PB. I can take a picture and label the wires if you need when I get hime from wok today (should be...

Take note of the original post- he asked if someone made an adapter, and for a link to someone he could contact about it. The place that has been mentioned (Dr. Tweak/Pheonix tuning- diff name, same guy) has a VERY good reputation and makes quality harnesses that have been proven reliable. If...

It will, the ECU needs to know how fast the car is moving to know when to shift!

At the rate that build is going, the stock manifold will likely be ditched in favor of a larger plenum volume one (ffim, my guess).

What's the plan for a hold-down plate for them?

Not really- the boots are fixed length and you don't really want to give any insulation up in that end. The connector also angles upwards, so that doesn't help a lot, either. Even still, I have a set of 6 to install on my car if the vvti 2jzge coils run out of power for me. Function > Form imo

No real power goal, just go until I feel 'done' Based off of what I've done driving so far, it seems like the car is getting close. Just trying to get the most out of what I already have installed and trying to get rid of restrictors. I agree with morning air being the best- makes the whole...

If Ian hadn't sold his group-A prepped rear drivetrain (had 3:1 gears iirc) and I was a baller like him I'd be all over it. Unfortuntely a V160 uses 3.2:1 gears to operate properly :'( That's why the T56 is such an appealing swap- but I require a speedo and ABS to operate(brake balance is way...

But no matter if Nick or I am right, a new starter is the fix for both conditions! (just be sure to inspect the teeth on the flywheel/flexplate while you have the starter out) Edit: lulz :P Glad you didn't need a new part :D

I went to the first Powercruise ever in the US this last weekend, which was the most fun I've ever had in my Supra, period. Although its a work in progress, here's what I have made as far as movies go... http://www.youtube.com/watch?v=BOgzJNmnT5w old movie... New one...