Search results

Okay - again this subject raises it's head, and it'd been done to death. The GE cam will *not* give you more power - all it'll do, is shift the power further down the rpm band by about 500rpm.

Just an FYI - i was WRONG earlier - it's not the Zetec-E or -R shims you need, its the Zetec-SE / Ford Sigma Engine ones - i'm still trying to get a hold of these! :(

Aaaah okay :) Did that datasheet reveal anything new? *edit* There's another one of these cropped up: http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=290412379557

The moment you can afford one of those, is the moment you can hire me :D

In with a small crowd.

Just as an FYI - i also got hold of some decent hires internal shots of the 1JZ Auto ECU, three D151802's in there - two 64-pins and a 42-pin and it looks a lot harder to decipher, as not even the silkscreening gives anything away! Can post them up out of general interest if you want.

We should chip in $5 each and get you one for christmas ;)

I'll start off with headphones: http://www.sightandsounduk.com/catalogue/p7710/s148_c143/Headphones/Banded-Headphones/Grado-PS1000.aspx *drools all over himself* The only stipulation is - it can't be a car, it has to be unnecessary and it must be stupidly expensive. Like, a solid gold Parker...

In with Zum.

Thanks dude. Did that PDF come in handy at all? *edit* Not finding ANY matches to anything by Fujitsu TEN - who seem to make only car audio stuff these days. Is there anything silkscreened onto the PCB with an IC number or something? Can anyone else with one of these post up an interior...

40 mile round trip - the cost of the fuel alone is more than the shims. I'll have to order them from the UK more than likely...

If you have a picture of the board, i'll start doing some research. Was looking at the Fujitsu Operand /Mnemonic lists - doesn't look too similar to what we're pulling out of the ECU - which is odd... *edit* Well, i think i figured out something - the MB88400 series datasheet i have only...

Sure thing boss :) http://kai.robinson.free.fr/dropbox/Supra/Fujitsu%20MB88400%204-bit%20MCU.pdf And this is the whole MB88 series lineup, for comparison purposes: http://kai.robinson.free.fr/dropbox/Supra/Fujitsu%20MB88%20Series%20MCU.pdf There you go!

GRRR - Fucking Ford! They gave me the WRONG SHIMS! >_< Money pissed down the fucking drain thanks to their incompetence... Looks like its the Zetec-SE and not the Zetec-R - lemme look into this a bit more...

In for a bit while i go through datasheets...

Nope - the datasheet labelled as the TD6335 came up as the 6330 which is the stepper motor driver - it's like the only Toshiba IC that DOESN'T have a datasheet, other than the main CPU... On that subject, it may have been mentioned before, or common knowledge, but comparing the Toshiba 8x with...

In for a bit...

GODDAMMIT! I am *such* a noob....just checked the hosts file against what the *actual* ip is. Turns out that facebook just migrated servers, and as i had hard coded the ip address for all of facebooks servers into the hosts file, just in case DNS failed on me (it does every now and then), i...

Still having issues when it comes to loading facebook, tracked it down to the fact that static.ak.fbcdn isn't loading at all. If i use https, then FB loads, because the SSL servers are on a different IP. So, tracert with static.ak.fbcdn.net reveals that everything is fine up until the point...

How do you know they flowtested them improperly? Did you watch them do it? For peace of mind, to rule them out, just get them done again. I have a set of 550cc RC's here that i got flowtested anyway, before i installed them in the fuel rail. If they had shown a discrepancy, i wouldn't have...