Search results

  1. I

    Low profile headlights

    Ridiculous :p
  2. I

    R154 here I come

    A built 340 makes for a nicer Supra ;)
  3. I

    Ball Bearing VS Journal Bearing and size!

    "Billet" wheels don't actually spool faster, they have more fin area due to the slimmer/smaller hub so move more air so "lag" feels like it's reduced ;) Might be a different matter if it were a Turbine wheel we were discussing. PMoI on the Billet wheel might be lower but I'm guessing the...
  4. I

    *MHG Reuse*

    Stoppers only come in 86mm. Used one on a stock bore 7M with no obvious dramas.
  5. I

    Mishimoto radiator redesign is in......FAILURE

    You're welcome! I actually went to the trouble of doing some drawings taking pics and sending PWR a stock Rad for a pattern, Mishi might benefit from this approach as they seem "willing" to work with the customers on this.
  6. I

    Half-Shaft to Diff bolts

    Very welcome! Good to hear it's all sorted, well done.
  7. I

    A new mini CNC mill and rebuildingy style) and in the process of building my old one.

    Ahh ok, just trying to get a scale on the work piece.
  8. I

    A new mini CNC mill and rebuildingy style) and in the process of building my old one.

    Is that a quarter beside it in pic 1?
  9. I

    Half-Shaft to Diff bolts

    I use a couple of pry bars and it pops out, reused the snaps quite a few times as I was too lazy to drive to Toyota ;) (snap rings actually hold the whole Stub axle in, that drawing is deceptive, the seal/cover end up at the flange end when installed with the seal staying in the pumpkin and the...
  10. I

    Importing from Japan.

    Might want to pull your head in there sparky....:nono: (I have 2x LS's) You don't actually have a clue what you want and don't have the $ to fund it so it was just a suggestion from someone that has "been there done that"..
  11. I

    Any engine parts i can take off a sc300 or sc400 for y 7MGE

    Always calm ;)
  12. I

    japan classic car show

    Don't know if it was meant to but that stings :p <jk>
  13. I

    Importing from Japan.

    LS made my already good handling Mk3 better..
  14. I

    japan classic car show

    If you do I hope you'll stick around here and post the progress in Members Rides. :)
  15. I

    Over heating while driving

    Fins can get blocked with leaves/bugs and crap over time and it sneaks up on you, get a warm day and off the needle goes where it's never been before.... This is what I meant by "marginal cooling system" in my 1st post.
  16. I

    Half-Shaft to Diff bolts

    Pop the Stub axle out (it's held in with a clip) so you can work on it on the bench. If you have a spare diff just swap in the stub if you can get a stud just open a vise enough so the back end of the stud is just held then smack it hard with a hammer where it's broken, it should pop out.
  17. I

    MA70 OEM Suspension - Bushes, or Spherical Bearings?

    No it's one of the 2 marked "bushing" it's in fact a bearing, the circled hole is for the arm with the ball joint end on it. Another important point when working on these is to NOT tighten any of the factory bushings until the cars weight is on the ground or you'll tear the centres out in a...
  18. I

    Over heating while driving

    Plastic undertray goes from the Lip to the Rad support then to the crossmember, car will run +5c with it missing and if your cooling system is marginal to begin with this is often enough to tip it over at highway speeds as the air can bypass the radiator.
  19. I

    Any engine parts i can take off a sc300 or sc400 for y 7MGE

    Make a better mooring point than an anchor too damn heavy to pull back up ;)
  20. I

    Over heating while driving

    Undertray?
View older results
Top Bottom