Search results

Hello All, Although this is not my first post, it is my first post that is after reading the "Dealing with the Oldschool guys." I felt a bit compelled to drop an intro at that point. I have had the fortunate luck of aquiring an 86.5 n/a with BHG, and needing a Timing Belt replacement along...

Okay cool I will redo the timing again. I wanted to check here first to see what everyone responded with, so far she runs, a bit rough just due to idling(timing i would say :). I also have a fuel leak. Going to check everything out in the daytime.

Cool, I did not short the T and E1 on the diag connector while checking timing. How crucial is this?

First off huge thank you to AJ for the help. It was timing. She lives now. So i picked up a 50 dollar timing light at Autozone today, has an anolog knob and a button to make it light up. From what I can judge, when the crank marker is lined up at the 0 on the timing cover. My timing...

I took a break this weekend, fiance was pissed I'm spending more time on the car than with her. I have to clean up in the garage tonight, I hate working with a mess. Then I'm going to get back on the ball. Thanks for the help, I'll try that which you mentioned and report so you know how...

Yes everything was aligned correctly upon installation. That is the odd part, after cranking i noticed she was (estimated)5 degrees negative(opposite side of the zero that has no markings). I readjusted my Timing Belt several times last night and it keeps getting off with the timing, I don't...

Sounds like your problem maybe beyond the gasket itself. I used ebay gasket and RTV blue sealant. No leaks so far, then again my car won't start either :( You may want to check the head and manifold to make sure there is no damaged surface area. You may have a groove or something causing the...

Supra4ever68, AFM is connect, :( I wish it were that simple. AJ, I'll verify timing tonight after work. Is it safe to turn the crank to align everything? I'm somewhat nervous about doing so(I know I did it when I took the head off this time around it's a little more scary where...

Well, I just finished filling up my radiator with a 50/50 mix and i tried starting my car after I put the engine back together. I found a few misc leaks(drain cock on block was a tad loose and the FPR as well on the fuel rail). Noticing that fuel came out of the FPR both front and rear of the...

Sweet, thanks guy.

Hello, I've been trying to do research and can't find too many answers for what I'm looking for. I would like to change trans and rear end fluid soon and wanted to get a general idea of what my best bet is. IE for example In my 02 Eclipse i use to run 2/3's BG Syncromesh and 1/3 Redline MTL...

Here! The hose in this picture, someone please tell me where this booger connects to. I would greatly appreciate it!! Looking over the posts i see AJ's 88NA reply. I feel dumb :) Oh well, at least this problem is resolved, thanks again Fellas.

Alright pimps, I have another question pertaining to this topic, where on the TB does the hose attach to? I think I'm going to have to post some pics to show diagrams of areas I'm refering to, I found the two lines that go from the upper manifold to the TB(the part of the TB that faces towards...

freaking awesome thanks fellas, I got tied up at work last night, however i should be good to hit it hard tonight.

There is a coolant hose under intake runner number 3, does anyone have a clue what it connects to? I'm trying to put the final touches of my engine back together and for the life of me I cannot recall what it goes to. I'll try to find a picture.

Hello, currently almost done rebuilding my 7MGE and had a question concerning the fan/clutch assembly that attaches to the water pump. I replaced my water pump and still have the fan and clutch assembly attached to the old water pump. It's a B*#%W# to remove since it's an 86.5 and I'm...

Hello all, I'm in the process of reassembling my 7M after an HG job and cleaning, painting a few parts in the process and doing minor upgrades(nothing serious unfortunately). I stumbled into a question, does the alternator bracket fit behind the a/c compressor and between the block? Or...

Thank you, now I've read a lot of people using brake quieter on their MHG to help it seal. Did you do this on your MHG as well? I'm thinking about doing this since I did not have the block shaved/lapped.

Hello all, I would like to give a breif introduction since this is my first post. I have been dissassembling and playing with a my 86.5 na Supra for a little while now. It had a bad stock HG with 138K on the odometer. Amongst other things going wrong with the car the engine was in...