Search results

Okay, so there is no B2 connector on this engine harnesss and many of the M1/B1 connector wires do not match up to what's been published for the pre-89s. I've worked out many of them and am tracing to confirm, but has anyone already got a wire mapping for a swap into an 86.5 N/A with no TEMS...

Seems to be covered well in the TRSM, but hoping someone may have a link to some write-ups I can follow along with (w/tips & tricks). Been searching, but haven't found any. TIA!

Okay, so I finally figured out the issue with my A/C compressor's clutch not kickin' on. Seems that the ECU is no longer supplying the ACMG signal. I wired it up, like the pic below. I have searched and searched and not found the original thread talking about doing it this way. Since it's...

Okay, so I am using the wiring config shown in this pic below, with my Aristo ECU... I had accidentally disconnected the 2 wires shown, over the Winter. I dunno if they made contact with anything. At this point, cigarette lighter is not working and the a/c magnetic clutch is not engaging...

On our 94 N/A, we took the Intake Manifold off and replaced everything back on as we thought it was supposed to be. Still sounds like we missed a vacuum line and I can't see where I may have missed it either. Car still runs fine, but I would still l ike to see a good detailed pic as well and...

Okay, so the driver's side rear wheel sticks out slightly more than the opposite side. causing some slight rubbing issues. Anyways, seems that other may have the same type of condition... http://supraforums.com/forum/showthread.php?t=551627 Also seems like it'd be easy enough to loosen...

Replaced the JVC head unit with a Sony recently. Every once in awhile, the JVC would just appear to turn off and then back on. Then just stopped doing it for a long time. I installed the Sony a few weeks back and just today, it rebooted 3x on my way into work. By reboot I mean it appears...

Anyone have good success with new, aftermarket ones? Specifically, those that still have the seatbelt-fastened sensor/connection, like stock.

I got the bixenon deal and some e-code housings. I don't like how the light's dispersed, so would like to know/see how others may have installed their HIDs, where they are VERY satisfied with the results. If you used the Hella housings, please post pics/feedback. The housings I used are...

So, I hate my center console. Only good for resting my arm on. I would like to customize it (maybe using fiberglass), so that it would have a functioning cup holder (away from the shifter) and maybe a couple of spots for guages, warning lights, etc. So has anyone seen something custom...

Okay, Can't figure this out. I have the 5-speed shifter and the rubber boot/insulator deal, but the bracket's holes don't line up with the holes that the auto-shifter did. I want to use the rubber insulator to dampen noise and keep out debri, etc. Anyone else do something that effectively...

I am finally getting around to installing my HIDS from a previous CK-group buy. I was hoping this would only take about an 1-hour, but I have already spent that much time searching for info on correctly installing/modifying everything. So, can ya'll please help with these questions...

Finishing my alarm install (hiding it properly) and am getting ready to install an auto-window-up deal that rolls the windows up when the alarm is armed. I have used the alarm install info from the Tech-tips section, but did not see anything about this. Does anyone have some experience...

Okay, I'm tired of not being frozen in my MKIII, like when it had R12. I am getting spare pieces of the A/C components together, so that we can have accurate dimensions/measurements for potential upgrades to the parts for our MKIIIs with R134, to make the air blow freezin' cold. What do we...

Might be old news, but I was looking to replace my hood struts,, but the only thing Autozone had in stock was the hatch struts. Knowing how much these cost from Toyota, just thought I'd share that I found them and they have a universal-type of bracket that should make it a direct replacement...

I searched... I have a knock in the rack, right at where the rubber boot is on the driver's side. It is present when I turn the wheel at slower speeds and is DEFINITELY not a grind. Had it checked out a couple of weekends ago and the shop found that the lower ball joint nut was coming...

Gettiing things together to have Josh start/finish the 2JZ-GE swap into the 1990 Supra. I plan to sell this Supra locally, after the swap's done. So, I have the GE that will be going into it and am rebuilding it. Just new rings, bearings, seals, headgasket, etc. I am sure that this will...

There are universal sets available from Energy Suspension. Since I've done the poly bushing upgrade, that's what I am thinking of going with. What've ya'll done, when still using the stock swaybars? Autozone's got 'em for ~$22 for the fronts, but I'd rather go poly to match 'em up with the...

I've got the shadow grey interior as well as the dash and some other vinyl/plastics dyed/painted black. So, I want to get some black seatbelts instead. I would like skrait black and am wondering if anyone's used them from another Toyota/Lexus... SC300, Celica, MKIV, etc? I'd want to still...

Tried the E85 and failed the 2nd test. They took it right in w/the cat still hot. Numbers were worse than before. Would rather get my single/Aristo ECU working right, so that things are running more efficiently, instead of trying to game the inspection. We are going to do the exact same...