Search results

i bought a 7m a while back from someone who gave up on their build. All the machine work has been done but I have some Q's. First, it is unassembled, bored .020 over for probe pistons, has shot-peened and cryo-treated stock rods, a 6m crank and all ARP hardware. He said he got everything zero...

building a high hp 7m, just curious about crank scrapers. Do they make a difference? worth the money? does it matter if you're using a 6m or 7m crank?

I'm building a high hp 7m and was looking at getting an accusump setup. I need to know all the pieces i need and exactly how to plumb it in relation to a remote filter and oil cooler system. I'm using an upgraded oil pump and trying to do everything I can to protect this engine. Any help...

found this today http://norfolk.craigslist.org/ele/1942664521.html

Glenn and I have already acquired suppliers for some parts and are in process of getting more. We are already taking some customers and are about ready for more. We will obviously specialize in 7m's, but will work on just about any car, (even Brandon's Mustang:icon_razz). We also want to get...

I was thinking about getting one and wanted to know how well they work.

I just installed a new South Bend clutch into my '87T. When I let off the pedal, there is a slight grinding noise and I only get about 5% grip. The car barely made it around the block and I couldn't even get it back in my garage. I figured I might have had a brain fart and put the disc in...

Found this just now. http://norfolk.craigslist.org/ele/815492341.html

I am trying to remove my pilot bearing. The grease trick didn't work, a bearing puller didn't work, a slide hammer didn't work. I drilled it, got the inner race and bearings out, that leaves just the outer race. A slide hammer and puller won't grip it, a sawsall won't cut it, a hack saw won't...

http://www.rotawheels.com/rb.php I want some that look like this, but in 17's. I need some decent width, too. I don't know where to find them.

I just thought people thinking of upgrading their turbos might want to see the difference between stock and the 57 trim. This was done by Driftmotion.

I need a mechanic that is good with 7m's. I had one in Texas but now I really need help. Anyone?

I posted a few weeks ago asking about a stuttering problem. I installed a coil pack ground wire and checked the timing. I can't get the timing on 10 degrees. I figured it was a tooth off but changing that didn't help. I did notice that it doesn't stutter until it is warm and only at...

I changed my front seals and timing belt recently. It ran great for about ten minutes, then it started stuttering any time I touched the gas. It got worse and worse until it would do it all the time. I found out the timing gear jumped a tooth. I corrected that but it didn't help. After...

Can you tighten the e-brake, and how? Also, can you put and aftermarket handle on it?

I have an '87 turbo Supra. I am getting a 1j to swap in. I know I can use the R154 but do I need a different bell housing? What else can I use so that I don't have to use a full front clip? In other words, if I just buy the engine itself, what else will I need other than harness, fuel pump...

I will probably get to go to TX2K7 but I wanted to know if anyone wanted to share a room or has a place I could crash. Also, what is up with the caravan from Dallas, where, when and who? If anyone isn't able to bring their Supra, (Matt, Poodles) you can ride with me if you want.

I need to borrow a driveshaft for a turbo 5-speed. I my get to go to TX2K7 but my carrier bearing is shot. Can anyone help me?

I am leaving for VA next month so this is my last chance to attend a meet, so I will start it. March 10 is basically the chance I have. feedback and suggestions are welcome. New location: Grapevine Mills at the north end next to the movie theater. New time: 5pm