Search results

Ok so my am2 fuse keeps popping and im trying to see what all is on the circuit. Im trying to trace down a short. Any help is greatly appreciated thanks

has anyone tubbed the front end of thier car? im looking to do this to take care of some developing rust issues also is it possible (safe lol) to just cut the metal away and run it open like the rx7 or frs? pics welcome

Hey everyone im having an interesting issue. The engine cranks all day but wont start. when i jumper fp to B+ the fuel pump does not turn on (upon further inspection B+ actually has no voltage in the check connector). when i jumped power from the battery to the B+ the engine runs fine. im...

hey my rear end got a little crunched the other day in an accident my drivers side tail light got crushed and im looking to replace it with a set of the led brake lights used on track cars. does anyone know where i might be able to find some of light bars ?

has anyone found or used an external latch on their front or rear bumpers to make them quick release? thanks

hey everyone i've been playing around with the idea of using a 240sx short throw shifter in the w58 they are roughly the same size as the c's and a fraction of the cost I have one laying around and ill be attempting this today and we will see if it actually works has anyone tried this before?

hey does anyone know of hand what the thread pitch of the inner tie rod is (where it attaches to the outer tie rod)? thanks

hey everyone im running into some interesting issues with my setup im starting to rub my front wheels on compression at speed im thinking i can keep this from happening by preloading the springs just past the point where each corner droops is that right? or will i just need higher rated...

ok i was looking around for this but had no luck. does anyone know of an aftermarket bumper that incorporates the header panel (nose cone)?

i had to remove my dash to get better access to some wiring i wanted to clean up but my dash was cracked and fugly so i decided to find out what was underneath if anything at all im liking what ive found so far. i think some more cleaning off of the glue and a coat of plasti dip and ill...

hey everyone im looking to put a custom 3 row radiator in place of my ac condenser(ac has already been ditched) any ideas on how to accomplish this? i saw viper had done this on his car but i havent been able to get him via pm so im posting it up to everyone any input is greatly...

hey everyone im looking to get some advice on replacing the rear fender wells. i have some good ones from a parts car but im unsure of how to remove and install them. i have my drill and my welder ready to go. any advice would be greatly appreciated

so i have found that my steering wheel turns more to the right than it does to the left. my question is can i fix this by centering the steering wheel so that it turns the same to the right and left then adjusting the tie rods so that the wheels are strait again? or will i mess things up by...

just wondering if there is an 8" rear pumpkin that we can use in our cars that anyone knows of

so im driving along today after adjusting my brake pedal to aleveate some serious squealing and the brakes seem to just want to apply themselves after a few min of driving everything ive read points to the brake booster (mine is from a toyota pickup due to my 1uz engine swap) anyone had this...

hey everyone last night after a fun night of getting sideways in parking lots i noticed a clunk coming from the drivetrain at first i thought the welds broke in the diff but thats not it diff is still locked up nicely. after searching on here ive concluded that my carrier bearing is just about...

hey everyone im looking into making a spool for our 7.5 rears (or scavenging one from another car that will work) im looking for the spline count for our axles and the bolt number for our ring gear thanks

Hey everyone i have a new project idea that im playing with and i need some info (and i dont really trust my math) im currently running a 97 1uzfe engine in my supra and im looking to go turbo, however there is a catch... i want to go remote turbo and i want to use a holset brand turbocharger...

hey everyone im looking into getting my first set of coilovers for my uza70 (1uz swapped)supra the goal i have for this car is to be a daily driver and weekend drifter. i neeeeeeeeed reliability. in your opinions what coilover set offers the best balance of stiffness reliability and height...

i think ive tried everything folks and to no avail my summer project is still kicking my butt i have replaced cats, ecu's, maf's and vacum hoses and i still have the same issue of the damn thing will not rev past 4k and is kicking black smoke from running extremely rich, i just have a few...