I hate to say it but I like this exhaust that I made

[NashMan]

Well my buddy Alex wanted me to make him and exhaust..... but a first I really didn't want to, but I caved and side why not I have bean planning an exhaust for some time.



So I made this for him


I even made a really neat down pipe for him.

 

[Mrbaboon]

And it sounds surprisingly good too! Way quieter than I thought it would be going from 3.5" to dual 3".

Compared to my last Nashman Special exhaust the turbo spools way faster..

 

[Turbo Habanero]

You must put a video of how it sounds !

Very nice work Nash i like it a lot.

 

[Suprapowaz!(2)]

Not bad Nash. A sound clip is a must.

 

[mk3_7m]

looks great. I'm a bit puzzled on the mid-section of the exhaust :S. Never the less can't wait for the vid

 

[bhmsupra]

its kinda JDM tyte bro!!!

 

[NashMan]

one pic is missing

 

[NashMan]

shit work time

 

[Suprapowaz!(2)]

Can we get pics of it on the car while it's on the ground? Does that system hang below the frame rails much?
Wouldn't it have been easier to use a muffler with both outlets on one side? Or did he just have that muffler laying around in his garage?

 

[Supra_dan]

Wow...that looks incredible!

 

[Mrbaboon]

Can we get pics of it on the car while it's on the ground? Does that system hang below the frame rails much?
Wouldn't it have been easier to use a muffler with both outlets on one side? Or did he just have that muffler laying around in his garage?

Ya I can post pics in a bit for sure. It hangs a bit below the frame rails at the muffler but I'm not lowered (yet) so its okay.

And yes, it would have been *way* easier to use a muffler with two exits on the same side but we would have had to wait another week or two, so we said f-it, we're making it work, hah.

 

[Hotwheelsjr]

And yes, it would have been *way* easier to use a muffler with two exits on the same side but we would have had to wait another week or two, so we said f-it, we're making it work, hah.

LOL...that's what this hobby is all about! Looks good!

 

[dmp316]

looks pretty nice. good job.

 

[DOUBL3 D]

That's raw I dig it!!! I wish I had access to welding equipment

 

[NashMan]

all try to get nice sound clip of it tomorrow if all goes well


but as for when it gets lowered it should be fine on a set of eibach springs since the car will have little rake to it, plus it only pokes past the frame rail by about 2 incs

 

[sixtyten6010]

What size are the exhaust tips you used? how long too? Are they straight cut as well?

 

[IJ.]

Looks restrictive with the 200 degree bend....

 

[suprarx7nut]

Are the internals of that muffler even close to that big? I thought most all magnaflows were 3" or smaller internally.

 

[NashMan]

well to answer some qestion's the exhaust muffler can it's self is 3.25 internal perforated pipe but factory it is 3 inc on the out side in let

now the dual 3 inc out is was 2.5 but again it just balloons out to 3 inc


over all it flow really well and quite with nice grumble and no drone what so ever if i is was just the one nasty bend then there would be some issues


the hole idea was to get rid of drone wich maganflows have alot of I find

 

[D.J.T.]

Looks restrictive with the 200 degree bend....

My thoughts exactly...
I think he should add a cutout